P2549 Code - Torque Management Request Input Signal 'B' Range/Performance
Quick Answer
To improve shift feel, the Transmission Control Module (TCM) may request that the Engine Control Module (ECM) reduce engine torque during shift events. Common causes include Faulty Engine Control Module (ECM), Faulty Transmission Control Module (TCM), Engine Control Module (ECM) software update. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P2549 indicates Torque Management Request Input Signal 'B' Range/Performance.
- Common causes
- Common causes include Faulty Engine Control Module (ECM), Faulty Transmission Control Module (TCM), Engine Control Module (ECM) software update.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P2549 Description
The torque reduction request is sent to the ECM through a communication network called the controller area network (CAN). Two circuits are used to communicate CAN data between the ECM and TCM.
A fault in the CAN will not cause the ECM to set the Diagnostic Trouble Codes (DTC). If a CAN fault occurs, other DTCs will set before this code.
The ECM set the OBDII code when the TCM receives a torque reduction failure message from the ECM.
What are the Possible Causes of the DTC P2549?
- Faulty Engine Control Module (ECM)
- Faulty Transmission Control Module (TCM)
- Engine Control Module (ECM) software update
- Transmission Control Module (TCM) software update
- Engine Control Module (ECM) harness is open or shorted
- Engine Control Module (ECM) circuit poor electrical connection
How to Fix the DTC P2549?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P2549 code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P2549 code?
Need more information on how to fix the P2549 code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P2549 code diagnosed by a professional: Find a repair shop in your area
Information for Specific Makes
- P2549 Buick — Torque Management Request Input Signal 'B' Range/Performance
- P2549 Cadillac — Torque Management Request Input Signal 'B' Range/Performance
- P2549 Chevrolet — Torque Management Request Input Signal 'B' Range/Performance
- P2549 Dodge — Torque Management Request Input Signal 'B' Range/Performance
- P2549 Ford — Torque Management Request Input Signal 'B' Range/Performance
- P2549 GMC — Torque Management Request Input Signal 'B' Range/Performance
- P2549 Lincoln — Torque Management Request Input Signal 'B' Range/Performance
- P2549 Mercury — Torque Management Request Input Signal 'B' Range/Performance
- P2549 Pontiac — Torque Management Request Input Signal 'B' Range/Performance
Frequently Asked Questions about P2549 Code
1. What are the common symptoms of OBDII code P2549?
The common symptoms of code P2549 include reduced engine power, poor acceleration, and the vehicle going into limp mode.
2. What are the possible causes of OBDII code P2549?
Possible causes of code P2549 include a faulty torque management request input signal 'B', issues with the throttle position sensor, wiring or connector problems, or a malfunctioning engine control module.
3. How can I diagnose the cause of OBDII code P2549?
Diagnosing code P2549 typically involves using a scan tool to read the code, checking the throttle position sensor, inspecting the wiring and connectors for damage, and testing the torque management request input signal 'B'.
4. Can I still drive my vehicle with OBDII code P2549?
It is not recommended to drive your vehicle with code P2549 present, as it can cause further damage to the engine and other components. It is best to address the issue promptly.
5. How serious is OBDII code P2549?
Code P2549 is considered a serious issue as it can lead to reduced engine performance and potential safety hazards on the road. It should be addressed as soon as possible.
6. What are some possible DIY repair tips for OBDII code P2549?
DIY repair tips for code P2549 include checking and cleaning the throttle position sensor, inspecting the wiring for any damage, and ensuring all connectors are properly connected.
7. Is it necessary to replace parts to fix OBDII code P2549?
Depending on the root cause of the code, parts replacement may be necessary. This could include replacing the torque management request input signal 'B', throttle position sensor, or repairing damaged wiring.
8. How much does it cost to repair OBDII code P2549?
The cost of repairing code P2549 can vary depending on the underlying issue and whether parts need to be replaced. It is recommended to consult with a professional mechanic for an accurate cost estimate.
9. Can a mechanic reset the OBDII code P2549 without fixing the issue?
While a mechanic can clear the code from the system, it is not recommended to do so without addressing the underlying problem causing code P2549. Simply resetting the code will not fix the issue.
10. How long does it take to repair OBDII code P2549?
The repair time for code P2549 can vary depending on the cause of the issue and the complexity of the repair needed. Some fixes may be quick, while others may require more time for diagnosis and repair.
Discuss the causes and fixes for P2549 OBDII Code
Code P2549 comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
