AutoCodes – Generic – B1019

B1019 Code - SDM System Configuration Error

Quick Answer

The Inflatable Restraint Sensing and Diagnostic Module (SDM) monitors the number of safety components installed on the vehicle. Common causes include Program Inflatable Restraint Sensing and Diagnostic Module (SDM), Faulty Inflatable Restraint Sensing and Diagnostic Module, Inflatable Restraint Sensing and Diagnostic Module harness is open or shorted. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

What it means: B1019 indicates SDM System Configuration Error.
Common causes: Common causes include Program Inflatable Restraint Sensing and Diagnostic Module (SDM), Faulty Inflatable Restraint Sensing and Diagnostic Module, Inflatable Restraint Sensing and Diagnostic Module harness is open or shorted.
Severity: High - diagnose this code as soon as possible.
Can I drive?: Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

Save to My Repairs My Repairs

AI answers can be wrong. Verify repairs with testing. Open full chat

Code Popularity 18,012

How popular is this code, among other codes? Low

Repair Importance Level

Urgent (Diagnose now) (3 / 3)

Repair Difficulty Level

Advanced (Pro) (3 / 3)

What is this?

Table of contents Created and updated by William Orellana on Apr 05, 2023

Description
Possible Causes
How To Fix
Tech Notes
Cost to Diagnose
FAQs
Comments
Add Comment

💬 Need more help? Ask Coddy for instant answers — it's free!

Code B1019 Description

The Inflatable Restraint Sensing and Diagnostic Module (SDM) monitors the number of safety components installed on the vehicle. When the ignition is turned ON, the Inflatable Restraint Sensing and Diagnostic Module evaluates the number of safety components installed and compares it to the number of components the Inflatable Restraint Sensing and Diagnostic Module expects to see on the vehicle with its current calibration. If there is a mismatch between the detected components and the components programmed with the Inflatable Restraint Sensing and Diagnostic Module calibration, Diagnostic Trouble Code (DTC) B1019 will be set. The components (if equipped) that the Inflatable Restraint Sensing and Diagnostic Module will detect include inflatable restraint deployment loops, impact sensors, passenger presence system components, seat position sensors, disable switches, and seat belt switches.

OBDII Code B1019 - SDM System Configuration Error - AutoCodes.com — B1019 Code - SDM System Configuration Error

What does this mean?

What are the Possible Causes of the DTC B1019?

Program Inflatable Restraint Sensing and Diagnostic Module (SDM)
Faulty Inflatable Restraint Sensing and Diagnostic Module
Inflatable Restraint Sensing and Diagnostic Module harness is open or shorted
Inflatable Restraint Sensing and Diagnostic Module circuit poor electrical connection

How to Fix the DTC B1019?

Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.

What does this mean?

Code Tech Notes

B1019:3A SDM System Configuration Error Incorrect Component Installed

Diagnostic Trouble Code (DTC) B1019 can be set after the Inflatable Restraint Sensing and Diagnostic Module (SDM) has been replaced and/or reprogrammed before the setup procedure is completed. The setup procedure cannot be completed if DTC B1019 is set as current or history. If a short or open is detected in a deployment circuit prior to the setup procedure being performed, the inflatable restraint sensing and diagnostic module will set DTC B1019.

What is the Cost to Diagnose the Code?

Labor: 1.0

To diagnose the B1019 code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.

Need more information about the B1019 code?

Need more information on how to fix the B1019 code? Get Access to Factory Service Manuals

Need Help with the Code?

Get the B1019 code diagnosed by a professional: Find a repair shop in your area

Information for Specific Makes

B1019 Buick — SDM System Configuration Error
B1019 Cadillac — SDM System Configuration Error
B1019 Chevrolet — SDM System Configuration Error
B1019 GMC — SDM System Configuration Error

Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service

Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.

Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.

About the author: William Orellana is a Master Mechanic and Mechanical Engineer with over 30 years of experience diagnosing and repairing vehicles. Learn more about his background.

Frequently Asked Questions about B1019 Code

1. What does the OBDII code B1019 mean?

The code B1019 stands for SDM System Configuration Error, indicating a problem with the airbag system in your vehicle.

2. What are the common symptoms of OBDII code B1019?

Common symptoms of B1019 may include the airbag warning light illuminating on the dashboard, the airbags not deploying in an accident, or other related safety system issues.

3. What are the potential causes of the B1019 code?

The B1019 code can be triggered by a faulty SDM (Sensing and Diagnostic Module), damaged wiring or connections in the airbag system, or a software issue in the vehicle's control module.

4. How can I diagnose the B1019 code?

Diagnosing the B1019 code typically requires using a professional OBDII scanner to retrieve the specific error code and then conducting further testing to pinpoint the exact cause of the SDM System Configuration Error.

5. Is it safe to drive with the B1019 code?

It is not recommended to drive with the B1019 code present, as it indicates a potential malfunction in the airbag system, which can compromise your safety in the event of a collision.

6. Can I reset the B1019 code myself?

While you can clear the B1019 code using an OBDII scanner, it is crucial to address the underlying issue causing the SDM System Configuration Error to ensure the proper functioning of your vehicle's airbag system.

7. How much does it cost to repair the B1019 code?

The cost of repairing the B1019 code can vary depending on the specific cause of the issue, but it may involve replacing the SDM, repairing wiring or connections, or updating the control module software.

8. Are there any DIY fixes for the B1019 code?

DIY fixes for the B1019 code are limited, as resolving this issue often requires specialized equipment and knowledge of airbag systems. It is recommended to consult a professional mechanic for proper diagnosis and repair.

9. How long does it take to repair the B1019 code?

The repair time for the B1019 code can vary based on the exact cause of the issue and the availability of parts. Some repairs may be completed in a few hours, while more complex issues could take longer.

10. Can the B1019 code be a recurring problem?

If the underlying cause of the B1019 code is not properly addressed, it can reoccur. It is essential to diagnose and repair the issue correctly to prevent the SDM System Configuration Error from coming back.