AutoCodes.com | All About OBDII Engine Codes
AutoCodes - Generic - U1102

U1102 Code - Invalid Or Missing Data For Primary Id

- Code Popularity: 48,638 Views
- Repair Importance Level: 3/3
- Repair Difficulty Level: 3/3
Table of contents
Share on Facebook   Share on Twitter   Share on Linkedin

What are the Possible Causes of the DTC U1102?

NOTE: The causes shown may not be a complete list of all potential problems, and it is possible that there may be other causes.
  • Faulty / intermittent ignition switch connections
  • J1850 / SCP / CAN Bus wiring intermittently open, shorted to power or ground
  • Faulty / intermittent connection at the Powertrain Control Module (PCM)
  • Faulty / intermittent connection at the Body Control Module (BCM)
  • Faulty / intermittent connection at the Instrument Panel Cluster (IPC)
⚠ Does your Car have Safety Recalls? → Check here

How to Fix the DTC U1102?

Review the 'Possible Causes' mentioned above and visually examine the corresponding wiring harness and connectors. Ensure to check for any damaged components and inspect the connector pins for signs of being broken, bent, pushed out, or corroded.

Code Tech Notes

This is typically an electrical wiring connection issue at one of the controllers being monitored by the manufacturer.
It can occur if:
Someone changes a battery while the ignition switch is left on, that is, left in the RUN position.
Someone flashes/upgrades their engine controller – other modules unable to communicate with PCM during this process – this will set U1102 at a multitude of controllers on the vehicle – all false codes. Erase and carry on.
May need to disconnect both battery cables and touch them together for 15 seconds. Reattach battery cables, positive first, then negative and see if a soft reset helps.

Search for U1102 Questions and Answers: Search here →

What is the Cost to Diagnose the Code?

Labor: 1.0

To diagnose the U1102 code, it typically requires 1.0 hour of labor. The specific diagnosis time and labor rates at auto repair shops can differ based on factors such as the location, make and model of the vehicle, and even the engine type. It is common for most auto repair shops to charge between $75 and $150 per hour.

When is the Code Detected?

When the Powertrain Control Module (PCM) is unable to communicate with any other controller on the bus network at any time while the ignition switch is in the RUN position.

What are Code Possible Symptoms?

  • Engine Light ON (or Service Engine Soon Warning Light)
  • Engine won’t crank / cranks but fails to start
  • Instrument panel gauges inoperative
  • Power windows / door locks intermittently operate
  • May or may not be able to communicate with a scan tool / depends on problem

Code U1102 Description

This is a manufacturer specific fault code and can be used for several different faults, depending upon what the manufacturer wants to use it for. Controllers communicate over the Serial Communication Protocol (SCP) bus network, also known as J1850 bus, or Controller Area Network or CAN Bus. These bus communication systems may or may not be fault tolerant, which means any type of intermittent/loose connection between these controllers could cause communication to stop. When these controllers are unable to communicate with each other at any time while the ignition switch is turned on, code U1102 will set.

OBDII Code U1102 - Invalid Or Missing Data For Primary Id - AutoCodes.com
U1102 Code - Invalid Or Missing Data For Primary Id

Need More Information on the Code?

Need more information on how to fix the U1102 code? Get Access to Factory Service Manuals

Information for Specific Makes

Need Help with the Code?

Get the U1102 code diagnosed by a professional: Find a repair shop in your area

Code U1102 comments

Help us improve AutoCodes.com. Leave a comment below or tell us if the information above helps you fix the code. What are the symptoms on your vehicle for the U1102 code? Have you replaced any parts?
Any information is appreciated. Thanks