P2544 GMC Code - Torque Management Request Input Signal 'A'
Quick Answer
To improve shift feel, the Transmission Control Module (TCM) may request that the Engine Control Module (ECM) reduce engine torque during shift events. Common causes include Faulty Engine Control Module (ECM), Faulty Transmission Control Module (TCM), Engine Control Module (ECM) software update. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P2544 GMC indicates Torque Management Request Input Signal 'A'.
- Common causes
- Common causes include Faulty Engine Control Module (ECM), Faulty Transmission Control Module (TCM), Engine Control Module (ECM) software update.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P2544 GMC Description
The torque reduction request is sent to the ECM through a communication network called the controller area network (CAN). Two circuits are used to communicate CAN data between the ECM and TCM.
A fault in the CAN will not cause the ECM to set the Diagnostic Trouble Codes (DTC). If a CAN fault occurs, other DTCs will set before this code.
The ECM set the OBDII code when the TCM receives a torque reduction failure message from the ECM.
What are the Possible Causes of the DTC P2544 GMC?
- Faulty Engine Control Module (ECM)
- Faulty Transmission Control Module (TCM)
- Engine Control Module (ECM) software update
- Transmission Control Module (TCM) software update
- Engine Control Module (ECM) harness is open or shorted
- Engine Control Module (ECM) circuit poor electrical connection
How to Fix the DTC P2544 GMC?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P2544 GMC code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P2544 GMC code?
Need more information on how to fix the P2544 GMC code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P2544 GMC code diagnosed by a professional: Find a repair shop in your area
Information for Specific GMC Models
- P2544 2014 GMC Sierra — Torque Management Request Input Signal 'A'
- P2544 2015 GMC Sierra — Torque Management Request Input Signal 'A'
- P2544 2016 GMC Sierra — Torque Management Request Input Signal 'A'
- P2544 2017 GMC Sierra — Torque Management Request Input Signal 'A'
- P2544 2018 GMC Sierra — Torque Management Request Input Signal 'A'
Frequently Asked Questions about P2544 GMC Code
1. What are the common symptoms of OBDII code P2544 in a GMC vehicle?
- Common symptoms include engine stalling, rough idling, decreased fuel efficiency, and potential issues with the vehicle's torque management system.
2. What does the Torque Management Request Input Signal 'A' code P2544 indicate in a GMC vehicle?
- This code indicates that there is a problem with the signal input related to torque management, which can impact the vehicle's performance and drivability.
3. What are the possible causes of OBDII code P2544 in a GMC vehicle?
- Possible causes include a faulty torque management sensor, damaged wiring or connectors, issues with the torque management module, or a software glitch in the vehicle's system.
4. How can I diagnose OBDII code P2544 in my GMC vehicle?
- Diagnosis typically involves using an OBDII scanner to retrieve the code, inspecting the torque management components, and performing a thorough check of the wiring and connections for any signs of damage or corrosion.
5. Can I still drive my GMC vehicle with OBDII code P2544 present?
- While it may be possible to drive the vehicle with this code present, it is not recommended as it can lead to performance issues and potential further damage to the vehicle's system.
6. How can I repair OBDII code P2544 in my GMC vehicle?
- Repair options may include replacing the faulty torque management sensor, repairing damaged wiring or connectors, resetting the torque management module, or updating the vehicle's software to address any glitches.
7. Is it possible to reset OBDII code P2544 in a GMC vehicle without fixing the underlying issue?
- While you can clear the code using an OBDII scanner, it is important to address the root cause of the problem to prevent the code from reappearing and ensure the vehicle operates properly.
8. How much does it typically cost to repair OBDII code P2544 in a GMC vehicle?
- The cost of repair can vary depending on the specific issue causing the code, but it may range from a few hundred to a few thousand dollars, including parts and labor.
9. Can OBDII code P2544 in a GMC vehicle cause damage if left unrepaired?
- Continued driving with this code present can potentially lead to further damage to the vehicle's torque management system and other related components, impacting overall performance and safety.
10. Is it necessary to visit a mechanic to repair OBDII code P2544 in a GMC vehicle?
- While some DIY enthusiasts may attempt to diagnose and repair this code themselves, it is recommended to seek professional help from a certified mechanic to ensure proper diagnosis and repair of the issue.
Discuss the causes and fixes for P2544 GMC OBDII Code
Code P2544 GMC comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
