P2544 2014 GMC Sierra Code - Torque Management Request Input Signal 'A'
Quick Answer
To improve shift feel, the Transmission Control Module (TCM) may request that the Engine Control Module (ECM) reduce engine torque during shift events. Common causes include Faulty Engine Control Module (ECM), Faulty Transmission Control Module (TCM), Engine Control Module (ECM) software update. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P2544 2014 GMC Sierra indicates Torque Management Request Input Signal 'A'.
- Common causes
- Common causes include Faulty Engine Control Module (ECM), Faulty Transmission Control Module (TCM), Engine Control Module (ECM) software update.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P2544 2014 GMC Sierra Description
The torque reduction request is sent to the ECM through a communication network called the controller area network (CAN). Two circuits are used to communicate CAN data between the ECM and TCM.
A fault in the CAN will not cause the ECM to set the Diagnostic Trouble Codes (DTC). If a CAN fault occurs, other DTCs will set before this code.
The ECM set the OBDII code when the TCM receives a torque reduction failure message from the ECM.
What are the Possible Causes of the DTC P2544 2014 GMC Sierra?
- Faulty Engine Control Module (ECM)
- Faulty Transmission Control Module (TCM)
- Engine Control Module (ECM) software update
- Transmission Control Module (TCM) software update
- Engine Control Module (ECM) harness is open or shorted
- Engine Control Module (ECM) circuit poor electrical connection
How to Fix the DTC P2544 2014 GMC Sierra?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P2544 2014 GMC Sierra code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P2544 2014 GMC Sierra code?
Need more information on how to fix the P2544 2014 GMC Sierra code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P2544 2014 GMC Sierra code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P2544 2014 GMC Sierra Code
1. What are common symptoms of OBDII code P2544 in a 2014 GMC Sierra?
- Common symptoms include engine stalling, rough idling, reduced engine power, and illuminated Check Engine Light.
2. What does the Torque Management Request Input Signal 'A' refer to in relation to code P2544 in a 2014 GMC Sierra?
- This code indicates a problem with the signal input that controls torque management in the vehicle's engine.
3. What are some possible causes of OBDII code P2544 in a 2014 GMC Sierra?
- Possible causes include a faulty torque request sensor, wiring issues, a defective Engine Control Module (ECM), or software problems.
4. How can I diagnose the cause of OBDII code P2544 in my 2014 GMC Sierra?
- Diagnosis typically involves using a scan tool to retrieve the code, checking the torque request sensor and related wiring for damage, and testing the ECM for proper function.
5. Can I continue driving my 2014 GMC Sierra with OBDII code P2544 present?
- It is not recommended to drive the vehicle with this code active, as it can lead to performance issues and potentially cause further damage to the engine.
6. Is it possible to reset OBDII code P2544 in a 2014 GMC Sierra without fixing the underlying issue?
- While you can clear the code with a scan tool, it is important to address the root cause of the problem to prevent the code from reoccurring.
7. Are there any DIY repair tips for fixing OBDII code P2544 in a 2014 GMC Sierra?
- DIY repair tips may include checking and cleaning the torque request sensor connector, inspecting wiring for damage, and ensuring proper connections to the ECM.
8. Should I take my 2014 GMC Sierra to a mechanic for OBDII code P2544 repair?
- If you are unsure about diagnosing or repairing the issue yourself, it is recommended to take your vehicle to a qualified mechanic for proper assessment and repair.
9. How much does it typically cost to repair OBDII code P2544 in a 2014 GMC Sierra?
- The cost of repair can vary depending on the specific cause of the issue, but it may range from a few hundred to a thousand dollars, including parts and labor.
10. Can OBDII code P2544 in a 2014 GMC Sierra cause long-term damage if left untreated?
- Ignoring this code can potentially lead to further engine problems and decreased performance over time, so it is advisable to address it promptly.
Discuss the causes and fixes for P2544 2014 GMC Sierra OBDII Code
Code P2544 2014 GMC Sierra comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
