AutoCodes – Generic – P2706

P2706 Code - Shift Solenoid 'F'

Quick Answer

The Transmission Control System uses six electronically controlled solenoids that allow hydraulic fluid to be applied to various friction elements (clutches), which enables the gear requested. Common causes include Dirty or Low Transmission Fluid, Faulty Shift Solenoid 'F', Shift Solenoid 'F' harness is open or shorted. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

What it means: P2706 indicates Shift Solenoid 'F'.
Common causes: Common causes include Dirty or Low Transmission Fluid, Faulty Shift Solenoid 'F', Shift Solenoid 'F' harness is open or shorted.
Severity: High - diagnose this code as soon as possible.
Can I drive?: Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

Save to My Repairs My Repairs

AI answers can be wrong. Verify repairs with testing. Open full chat

Code Popularity 16,819

How popular is this code, among other codes? Low

Repair Importance Level

Urgent (Diagnose now) (3 / 3)

Repair Difficulty Level

Advanced (Pro) (3 / 3)

What is this?

Table of contents Created and updated by William Orellana on Dec 27, 2020

Description
Possible Causes
How To Fix
Cost to Diagnose
Comments
Add Comment

💬 Need more help? Ask Coddy for instant answers — it's free!

Code P2706 Description

The Transmission Control System uses six electronically controlled solenoids that allow hydraulic fluid to be applied to various friction elements (clutches), which enables the gear requested. The continuity of each solenoid circuit is periodically tested. Each inactive solenoid is turned on for a few milliseconds, then off. Each active solenoid is turned off for a few milliseconds, then on. This pulsing of voltage to the solenoid causes an inductive spike which can be sensed by the Transmission Control System. If an inductive spike is not sensed by the Transmission Control System during the continuity check, it is tested again. If the test fails three consecutive times, the appropriate Diagnostic Trouble Code (DTC) is set. If the solenoid test is run in response to a gear ratio or pressure switch error, one failure will result in setting the appropriate DTC.

OBDII Code P2706 - Shift Solenoid 'F' - AutoCodes.com — P2706 Code - Shift Solenoid 'F'

What does this mean?

What are the Possible Causes of the DTC P2706?

Dirty or Low Transmission Fluid
Faulty Shift Solenoid 'F'
Shift Solenoid 'F' harness is open or shorted
Shift Solenoid 'F' circuit poor electrical connection

How to Fix the DTC P2706?

Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.

What is the Cost to Diagnose the Code?

Labor: 1.0

To diagnose the P2706 code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.

Need more information about the P2706 code?

Need more information on how to fix the P2706 code? Get Access to Factory Service Manuals

Need Help with the Code?

Get the P2706 code diagnosed by a professional: Find a repair shop in your area

Information for Specific Makes

P2706 Chrysler — Shift Solenoid 'F'
P2706 Dodge — Shift Solenoid 'F'
P2706 Jeep — Shift Solenoid 'F'
P2706 RAM — Shift Solenoid 'F'

About the author: William Orellana is a Master Mechanic and Mechanical Engineer with over 30 years of experience diagnosing and repairing vehicles. Learn more about his background.