C1130 Infiniti Code - Engine Signal 1
Quick Answer
ABS actuator and electric unit (control unit) and ECM exchange the engine signal with CAN communication line. Common causes include Faulty Engine Control Module (ECM), Faulty ABS actuator and electric unit (control unit), Control Area Network (CAN) communication line. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- C1130 Infiniti indicates Engine Signal 1.
- Common causes
- Common causes include Faulty Engine Control Module (ECM), Faulty ABS actuator and electric unit (control unit), Control Area Network (CAN) communication line.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code C1130 Infiniti Description
What are the Possible Causes of the DTC C1130 Infiniti?
- Faulty Engine Control Module (ECM)
- Faulty ABS actuator and electric unit (control unit)
- Control Area Network (CAN) communication line
- Blown ECM fuses
How to Fix the DTC C1130 Infiniti?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
Code Tech Notes
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the C1130 Infiniti code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the C1130 Infiniti code?
Need more information on how to fix the C1130 Infiniti code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the C1130 Infiniti code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about C1130 Infiniti Code
1. What are the common symptoms of OBDII code C1130 in an Infiniti?
- Common symptoms include rough idling, decreased engine performance, and potential stalling.
2. What does OBDII code C1130 indicate in an Infiniti?
- OBDII code C1130 in an Infiniti indicates an issue with Engine Signal 1, which could be related to the ignition system.
3. What are some possible causes of OBDII code C1130 in an Infiniti?
- Possible causes include faulty ignition coils, damaged wiring in the ignition system, or a malfunctioning Engine Control Module (ECM).
4. How can I diagnose the source of OBDII code C1130 in my Infiniti?
- Diagnosing the issue may involve checking the ignition coils, inspecting the wiring for damage, and using a diagnostic scanner to read live data from the ECM.
5. Can I continue driving my Infiniti with OBDII code C1130 present?
- It is not recommended to continue driving the vehicle with OBDII code C1130 present, as it can lead to further engine damage or safety hazards.
6. Is it possible to reset OBDII code C1130 in an Infiniti without fixing the underlying issue?
- While you can clear the code temporarily, it will likely reappear until the underlying issue causing code C1130 is resolved.
7. Are there any DIY repair tips for fixing OBDII code C1130 in an Infiniti?
- DIY repair tips may include visually inspecting ignition components, checking for loose connections, and ensuring proper grounding of the ignition system.
8. How much does it typically cost to repair OBDII code C1130 in an Infiniti?
- The cost of repair can vary depending on the exact cause of the issue, but it may involve replacing ignition coils, repairing wiring, or reprogramming the ECM.
9. Can a mechanic easily fix OBDII code C1130 in an Infiniti?
- A qualified mechanic with experience in diagnosing and repairing engine issues should be able to efficiently address and fix OBDII code C1130 in an Infiniti.
10. Will OBDII code C1130 cause my Infiniti to fail an emissions test?
- Yes, OBDII code C1130 can cause your Infiniti to fail an emissions test, as it indicates a potential issue with the engine's ignition system.
Discuss the causes and fixes for C1130 Infiniti OBDII Code
-
The C1130 means that the Antilock Brake System (ABS) is not receiving the a signal from the Engine Control Module. There should be a code in the Engine Control Module (ECM) something like Pxxxx. Whatever is triggering the engine code it's probably the cause of the problem. Code in the ABS system usually will not cause the engine to stall. In other word the C1130 is not the cause, is the result.
-
I just began having this exact problem myself. Car shut off in traffic twice, full tank of gas and everything. Check engine, slip ,and ABS are all illuminated on the dash... getting codes "C1130 and P0340" Thank you in advance for help..
03 G35 Coupe 151K
-
The problem is more than likely the camshaft position sensor.
P0340 2003 INFINITI G35 - Camshaft Position Sensor Circuit Bank 1
Read more: http://www.autocodes.com/p0...
-
No, the C1130 is more than likely triggered because something else is causing the rough idle and power loss. Common causes for the symptoms are fuel pump and ignition coils.
-
My fuel pump and ignition coils are fine. I just swapped my transmission and ever since then I lost almost all power. My ecu is blocking the scanner from reading it it keeps saying no communication and not entering the system I swapped out spark plugs. Catalytic converter.
02 sensors and more and still nothing. Bogs and no power at all. And even in park and neutral the car doesn rev right when pressing the gas -
Did you use a new, rebuild or used transmission? The transmission you are using is probably not compatible with the the ECM on your G.
-
As far as I know the only solution is to have the dealer reprogram the TCM and ECM
-
Non of the codes are directly related, but the most important is the P0335. I recommend starting by clearing all the codes first. If all the codes come back, you should start by fixing the P0335 code, which is the most important and common one.
P0335 2005 INFINITI G35 - Crankshaft Position Sensor Circuit
Read more: http://www.autocodes.com/p0...C1145 INFINITI - YAW Rate Sensor
Read more: http://www.autocodes.com/c1... -
I recommend fixing the crankshaft position sensor first, because that may take care of the the other two sensors.
Yaw sensor is under the center console.
For the C1130, you could start by clearing the code and cleaning the ABS control unit sensor. If the light comes back then you may have to replace the ABS control unit. -
Were is the abs control unit censor? And i was thinking of cleaning the maf sensor and the throttole body too and changing the camshaft and crankshaft sensor while im at it
-
Ok ill let you know what happens tomorrow if nothing works then im taking it to the dealership i have extended warrenty
-
have an 03 infiniti g35 and getting codes, p0345 c1109 c1155 and c1130. the car has been cutting out while in transit.
-
The "C" codes shouldn't cause the engine cutting problem. Mor than likely the problem is the Camshaft Position Sensor. If possible replace both sides, it's a common problem.
P0345 2003 INFINITI G35 - Camshaft Position Sensor Circuit Bank 2
Read more: https://www.autocodes.com/p...Before you replace the sensors, check with your local dealer, there was a factroy recall for the sensors.
2003 Infiniti G35 Sedan Service Recalls/Campaigns: http://x.infinitihelp.com/f...
-
Sounds like you may have a problem with the ABS Control Module, but that usually wont cause an engine performance problem. Have you tried clearing the codes?
Common causes for the engine to sputter are bad gas, spark plugs or fuel injectors. When was the last time you service (spark plugs and filters) your G35?
-
I have an 2004 infinity g35 I had the crank shaft position sensor fixed and a week later my car cut off and it's back to running under powered my check engine light came back on my vdc and my slip light came on as well now the code is c1130 and thats the only code what do I do ??
-
Unfortunately, this C1130 doesn't explain exactly what the problem is. Could b a problem with the ABS, the Engine Control Module (ECM) or a sensor. The SLIP and VDC lights, came ON because of the engine stall.
My best guess is that one of the "Camshaft Position Sensors" fail, cause the engine to stall and trigger the C1130 and the warning lights.
When one of the sensors (Camshaft or Crankshaft Position) fail, we usually recommend replacing all 3 sensors.
-
My G35 triggered 4 sensors after it kinda slipped at a speed of 80mph and then it the VDC, check engine, and slip lights all lit up. These are the codes c1130, p1815,p1705,p0340. Ideas on how to correct?
-
None of the codes circuits are related, you should start by clearing all the codes and checking the transmission fluid level and condition, then check what code (s) come back first.
P1705 INFINITI - Throttle Position Sensor
Read more: https://www.autocodes.com/p...P1815 INFINITI - Manual Mode Switch
Read more: https://www.autocodes.com/p...P0340 INFINITI - Camshaft Position Sensor Circuit Bank 1
Read more: https://www.autocodes.com/p... -
Looks like you may have two different problems, one with the ABS system and one with the key. Besides the engine light, do you have any other symptoms?
C1130 INFINITI - Engine Signal 1
Read more: https://www.autocodes.com/c...C1109 INFINITI - Power And Ground System
Read more: https://www.autocodes.com/c...P1614 INFINITI - Chain of IMMU-KEY
Read more: https://www.autocodes.com/p... -
2003 g35. codes c1130 and p035
car had problem starting up. changed the camshaft sensors on both sides. check engine light turned off but came back on the same day -
Is the P0335 code? if it is then the problem is the "Crankshaft Position Sensor" and not the "Camshaft Position Sensor".
P0335 2003 INFINITI G35 - Crankshaft Position Sensor Circuit
Read more: https://www.autocodes.com/p... -
Other than the Camshaft Position Sensors, I have not seen any other component triggering both the C1130 and P0345 codes. I've checked a national database of repairs for your model year and for 143 repairs with the same codes, the camshaft position sensor was the solution.
My only recommendation is to double check the the sensor connector. Many times the connectors pop of the sensor. -
Ive got a 06 G335 sedan 2wd Im getting the Code C1130, I was getting the code P0340 but i changed out the sensors already and that code is gone. The car inst starting not sure if you need that info or not.
-
Have you tried clearing the code? how long it takes to come back? is not common to have the C1130 code after replacing the Camshaft Position Sensor.
-
Yeah i cleared it and it doesn't come back, car still wont start but im not getting anymore codes.
-
Star by checking the battery charge. If the battery is OK, then check the alternator charging. If both are OK, then you could have a problem with the alternator
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
