C1109 Nissan Code - Power And Ground System
Quick Answer
The Anti-Lock Brake System (ABS) Module Actuator (Electrical / Control Unit) monitors the power supplies. Common causes include Faulty Anti-Lock Brake System (ABS) Module Actuator (Electrical / Control Unit), ABS Module harness is open or shorted, ABS Module circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- C1109 Nissan indicates Power And Ground System.
- Common causes
- Common causes include Faulty Anti-Lock Brake System (ABS) Module Actuator (Electrical / Control Unit), ABS Module harness is open or shorted, ABS Module circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code C1109 Nissan Description
What are the Possible Causes of the DTC C1109 Nissan?
- Faulty Anti-Lock Brake System (ABS) Module Actuator (Electrical / Control Unit)
- ABS Module harness is open or shorted
- ABS Module circuit poor electrical connection
- Blown ABS Module fuse
- Low battery voltage
How to Fix the DTC C1109 Nissan?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the C1109 Nissan code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the C1109 Nissan code?
Need more information on how to fix the C1109 Nissan code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the C1109 Nissan code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about C1109 Nissan Code
1. What are the common symptoms of OBDII code C1109 in a Nissan related to the Power And Ground System?
- Common symptoms include issues with power steering, ABS malfunction, and illuminated warning lights on the dashboard.
2. What are the possible causes of OBDII code C1109 in a Nissan related to the Power And Ground System?
- Possible causes include damaged wiring, faulty power steering control unit, corroded connectors, or a weak battery.
3. How can I diagnose OBDII code C1109 in a Nissan related to the Power And Ground System?
- Diagnosis involves checking the power and ground connections, inspecting wiring for damage, testing the power steering control unit, and scanning for other related codes.
4. Can a weak battery cause OBDII code C1109 in a Nissan related to the Power And Ground System?
- Yes, a weak battery can lead to voltage irregularities and trigger the C1109 code. Ensure the battery is in good condition before further diagnostics.
5. What repair tips can help resolve OBDII code C1109 in a Nissan related to the Power And Ground System?
- Repair tips include repairing or replacing damaged wiring, cleaning corroded connectors, replacing the power steering control unit if necessary, and ensuring all connections are secure.
6. Is it safe to continue driving with OBDII code C1109 in a Nissan related to the Power And Ground System?
- It is not recommended to drive the vehicle with unresolved C1109 code as it may affect the power steering functionality and ABS system operation, compromising safety.
7. Can OBDII code C1109 in a Nissan related to the Power And Ground System be reset without fixing the underlying issue?
- While the code can be cleared temporarily, it will likely reappear if the root cause is not addressed. Resetting the code without proper repair may lead to recurring problems.
8. How much does it typically cost to repair OBDII code C1109 in a Nissan related to the Power And Ground System?
- Repair costs can vary depending on the exact cause of the issue, but it may involve expenses for parts replacement, labor, and diagnostic fees. It is recommended to consult a professional for an accurate estimate.
9. Are there any recalls or service bulletins related to OBDII code C1109 in Nissan vehicles concerning the Power And Ground System?
- It is advisable to check with Nissan dealership or service center for any recalls or service bulletins related to OBDII code C1109 to see if the issue is covered under warranty or special service campaigns.
10. How can regular maintenance help prevent OBDII code C1109 in a Nissan related to the Power And Ground System?
- Regular maintenance, including checking and cleaning electrical connections, inspecting wiring harnesses, and ensuring proper battery health, can help prevent issues that may trigger the C1109 code.
Discuss the causes and fixes for C1109 Nissan OBDII Code
-
Hey I have a NISSAN CARAVAN NV350 YEAR 2012. Two weeks ago I replaced an old battery with a new one and by doing that I immediately got a ABS light on my dash board with an error code C1109 Speed control Actuator assembly cable release Failure. I have tried
1. Clearing the code
2. Replacing the fuse
3. Physically check the rear right and left wheel harness
Nothing is working so far.All this because I replaced my old battery with a new one
-
Some shops reported that a low battery charge will set the code. But obviously that is not your problem because you replaced the battery. My suggestion is to check the voltage of the battery with the engine running. The code will be set if the voltage is 10 V or less or 16 V or more. You could have a bad alternator that is not properly charging. Do you have any more symptoms or codes?
-
Below are the results of the battery test
while the ignition was off the battery was at 12.2V
Draw down during ignition went down to 9.42V
Charging voltage was at 13.02V -
Although 9.42V is within the range for most vehicles, it could be too low for your vehicle. Did you use the factory recommended battery? If you did, then check the battery terminals and cables for corrosion.
-
I have a 2015 nissan versa note sv 1.6 engine hatchback. We replace both oxygen sensors up stream down stream,MAF,temperature sensor new battery. And still have all this codes: P0037, C1109, C1142, C1107, C1106, C1105, C1143
-
I'm sorry to hear you're experiencing these issues with your 2015 Nissan Versa Note SV. Based on the codes you've provided and the components you've already replaced, it seems you're dealing with multiple electrical circuit issues that may be interconnected. Let's break down each of the diagnostic trouble codes (DTCs) and explore possible solutions.
Diagnostic Trouble Codes (DTCs)
-
P0037: Heated Oxygen Sensor (HO2S) Heater Control Circuit Low (Bank 1 Sensor 2)
- This code indicates a low voltage in the heater control circuit of the downstream oxygen sensor.
-
C1105: Right Front Wheel Sensor Open Circuit
-
C1106: Left Rear Wheel Sensor Open Circuit
-
C1107: Right Rear Wheel Sensor Open Circuit
- These codes suggest that the wheel speed sensors are not communicating properly, possibly due to open circuits.
-
C1109: Battery Voltage Abnormal (Brake Control)
- This code indicates an issue with the battery voltage supplied to the brake control system.
-
C1142: Pressure Sensor Output Voltage Low
-
C1143: Pressure Sensor Output Voltage High
- These codes point to inconsistent voltage readings from the brake pressure sensor.
Potential Causes
Given the variety of codes affecting different systems (engine, ABS, and brake systems), a common denominator is likely causing these issues:
-
Electrical Issues:
- Blown Fuses or Fusible Links: A blown fuse in a circuit shared by these components could cause multiple failures.
- Faulty Grounds: Poor grounding can lead to voltage irregularities across various sensors and modules.
- Damaged Wiring Harness: Physical damage or corrosion in the wiring harness can disrupt signal transmission.
- Connectors: Loose or corroded connectors can cause open circuits and voltage issues.
-
Battery and Charging System:
- Alternator Problems: An alternator that isn't charging properly can cause low voltage issues.
- Battery Terminals: Corroded or loose battery terminals can lead to voltage drops.
-
Control Module Failures:
- ABS Control Module: A malfunctioning module can throw multiple wheel sensor and pressure sensor codes.
- Engine Control Module (ECM): While less likely, a faulty ECM can misinterpret sensor signals.
Recommended Steps to Diagnose and Fix the Issue
-
Inspect Fuses and Fusible Links:
- Check all relevant fuses related to the ABS, brake system, and engine sensors.
- Replace any blown fuses with the correct amperage rating.
-
Check Battery and Charging System:
- Test the battery voltage with the engine off and running. It should be around 12.6V when off and 13.7-14.7V when running.
- Ensure the alternator is functioning correctly.
- Clean and tighten battery terminals and ground connections.
-
Examine Grounds and Wiring:
- Locate and clean all ground points connected to the affected systems.
- Inspect the wiring harness for signs of damage, wear, or corrosion.
- Pay special attention to the wiring near the wheel sensors and oxygen sensors.
-
Inspect Wheel Speed Sensors:
- Remove and clean the wheel speed sensors to eliminate any debris or corrosion.
- Check the connectors for secure attachment and absence of corrosion.
- Test the resistance of each sensor to ensure they are within specification.
-
Test the Oxygen Sensor Heater Circuit:
- Use a multimeter to check the voltage and resistance in the heater circuit of the downstream O2 sensor.
- Ensure the wiring and connectors are intact and properly connected.
-
Brake Pressure Sensor Evaluation:
- Inspect the brake pressure sensor and its wiring for any signs of damage.
- Test the sensor output voltage to see if it falls within the manufacturer's specifications.
-
Professional Diagnostic:
- If the above steps do not resolve the issue, it may be necessary to use advanced diagnostic equipment.
- A professional technician can perform module scans to check for communication errors between control units.
Possible Underlying Issues
- Common Ground or Power Supply Problem: Multiple sensor failures often point to a shared ground or power supply issue.
- Faulty ABS Module: Since several codes relate to the ABS system, the module itself may be defective.
- ECM Software Glitch: Although less common, sometimes updating the ECM software can resolve unexplained DTCs.
Next Steps
- Prioritize Safety: Since some of these codes affect the braking system, it's important to address them promptly to ensure vehicle safety.
- Consult a Professional: Given the complexity and potential safety implications, consider taking your vehicle to a certified Nissan technician for a thorough diagnosis.
- Document Everything: Keep a record of all repairs and diagnostics performed. This information can be invaluable for technicians.
I hope this information helps you identify and resolve the issues with your Nissan Versa Note. If you have further questions or need clarification on any of the steps, feel free to ask.
-
-
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
