AutoCodes – Generic – B1B01

B1B01 Code - Driver Airbag Squib 1 Circuit High

Quick Answer

When powered, the Occupant Restraint Controller (ORC) sends a test current to the squibs to verify the integrity of the squib and wiring. Common causes include Faulty Driver Airbag Squib 1, Driver Airbag Squib 1 harness is open or shorted, Driver Airbag Squib 1 circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

What it means: B1B01 indicates Driver Airbag Squib 1 Circuit High.
Common causes: Common causes include Faulty Driver Airbag Squib 1, Driver Airbag Squib 1 harness is open or shorted, Driver Airbag Squib 1 circuit poor electrical connection.
Severity: High - diagnose this code as soon as possible.
Can I drive?: Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

Save to My Repairs My Repairs

AI answers can be wrong. Verify repairs with testing. Open full chat

Code Popularity 3,198

How popular is this code, among other codes? Low

Repair Importance Level

Urgent (Diagnose now) (3 / 3)

Repair Difficulty Level

Advanced (Pro) (3 / 3)

What is this?

Table of contents Created and updated by William Orellana on Aug 14, 2019

Description
Possible Causes
How To Fix
Cost to Diagnose
FAQs
Comments
Add Comment

💬 Need more help? Ask Coddy for instant answers — it's free!

Code B1B01 Description

When powered, the Occupant Restraint Controller (ORC) sends a test current to the squibs to verify the integrity of the squib and wiring. These circuits are maintained in a "floating" configuration at the module (connected to neither power nor ground) as protection against inadvertent deployment. The use of the SRS Load Tool Adaptor provides a test point as well as a method for opening the shorting bar connections within the harness connector. The Clockspring is part of the Steering Column Control Module (SCCM). The SCCM includes the steering column shroud, the Steering Angle Sensor (SAS), the Clockspring, the Multi-function Switch, a Steering Column Power Tilt and Telescope Switch (if equipped), and a trim cover. The SCCM is replaced as an entire assembly. The ORC Module sends out a 40 mA diagnostic current on each squib voltage supply circuit at power up, and every 500 ms thereafter while the ignition is on.

OBDII Code B1B01 - Driver Airbag Squib 1 Circuit High - AutoCodes.com — B1B01 Code - Driver Airbag Squib 1 Circuit High

What does this mean?

What are the Possible Causes of the DTC B1B01?

Faulty Driver Airbag Squib 1
Driver Airbag Squib 1 harness is open or shorted
Driver Airbag Squib 1 circuit poor electrical connection
Faulty Driver Airbag
Faulty Steering Comun Control Module (Clockspring)
Faulty Occupant Restraint Controller (ORC)

How to Fix the DTC B1B01?

Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.

What is the Cost to Diagnose the Code?

Labor: 1.0

To diagnose the B1B01 code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.

Need more information about the B1B01 code?

Need more information on how to fix the B1B01 code? Get Access to Factory Service Manuals

Need Help with the Code?

Get the B1B01 code diagnosed by a professional: Find a repair shop in your area

Information for Specific Makes

B1B01 Chrysler — Driver Airbag Squib 1 Circuit High
B1B01 Dodge — Driver Airbag Squib 1 Circuit High
B1B01 Jeep — Driver Airbag Squib 1 Circuit High
B1B01 Mitsubishi — Driver Airbag Squib 1 Circuit High
B1B01 RAM — Driver Airbag Squib 1 Circuit High

Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service

Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.

Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.

About the author: William Orellana is a Master Mechanic and Mechanical Engineer with over 30 years of experience diagnosing and repairing vehicles. Learn more about his background.

Frequently Asked Questions about B1B01 Code

1. What are the common symptoms of OBDII code B1B01 (Driver Airbag Squib 1 Circuit High)?

- Common symptoms include the airbag warning light illuminated on the dashboard and a diagnostic trouble code related to the driver airbag squib circuit high.

2. What can cause the OBDII code B1B01 to appear?

- The code B1B01 is typically triggered by a high resistance or open circuit in the driver airbag squib 1 circuit, which can be caused by wiring issues, a faulty squib, or a poor connection.

3. How serious is the OBDII code B1B01 (Driver Airbag Squib 1 Circuit High)?

- This code indicates a potential issue with the driver-side airbag system, which is a critical safety component in the event of a collision. It is important to address this issue promptly to ensure the proper function of the airbag system.

4. Can I still drive my vehicle with the OBDII code B1B01 present?

- It is not recommended to drive the vehicle with the airbag warning light on and an active fault code related to the driver airbag squib circuit high. The airbag system may not deploy correctly in the event of an accident.

5. How can I diagnose and repair the OBDII code B1B01 myself?

- Diagnosing and repairing the B1B01 code may require advanced automotive diagnostic tools and knowledge of airbag systems. It is recommended to seek assistance from a qualified mechanic or technician to properly diagnose and repair the issue.

6. Is it safe to reset or clear the OBDII code B1B01 without fixing the underlying problem?

- Resetting or clearing the B1B01 code without addressing the root cause can be dangerous as it may lead to the airbag system not functioning correctly in the event of a collision. It is important to fix the issue before clearing the code.

7. Are there any recalls or technical service bulletins related to the OBDII code B1B01?

- It is recommended to check with the vehicle manufacturer or authorized dealerships for any recalls or technical service bulletins related to the B1B01 code. They may provide guidance on known issues and solutions.

8. How much does it typically cost to repair the OBDII code B1B01 (Driver Airbag Squib 1 Circuit High)?

- The cost of repairing the B1B01 code can vary depending on the underlying issue, parts needed, and labor costs. It is advisable to obtain quotes from reputable repair shops or dealerships for an accurate estimate.

9. Can a DIY enthusiast with automotive experience fix the OBDII code B1B01 at home?

- Repairing the B1B01 code may involve working with sensitive safety systems like airbags, so it is recommended to have specialized knowledge and tools. DIY enthusiasts with experience in automotive electronics may be able to diagnose the issue but should proceed with caution.

10. How long does it typically take to repair the OBDII code B1B01?

- The repair time for the B1B01 code can vary depending on the exact cause of the issue and the complexity of the repair. It may take a few hours to a full day to diagnose and fix the problem, so it is advisable to plan accordingly.