AutoCodes – Generic – B1B00

B1B00 Code - Driver Airbag Squib 1 Circuit Low

Quick Answer

When powered, the Occupant Restraint Controller (ORC) sends a test current to the squibs to verify the integrity of the squib and wiring. Common causes include Faulty Driver Airbag Squib 1, Driver Airbag Squib 1 harness is open or shorted, Driver Airbag Squib 1 circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

What it means: B1B00 indicates Driver Airbag Squib 1 Circuit Low.
Common causes: Common causes include Faulty Driver Airbag Squib 1, Driver Airbag Squib 1 harness is open or shorted, Driver Airbag Squib 1 circuit poor electrical connection.
Severity: High - diagnose this code as soon as possible.
Can I drive?: Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

Save to My Repairs My Repairs

AI answers can be wrong. Verify repairs with testing. Open full chat

Code Popularity 2,522

How popular is this code, among other codes? Low

Repair Importance Level

Urgent (Diagnose now) (3 / 3)

Repair Difficulty Level

Advanced (Pro) (3 / 3)

What is this?

Table of contents Created and updated by William Orellana on Aug 14, 2019

Description
Possible Causes
How To Fix
Cost to Diagnose
FAQs
Comments
Add Comment

💬 Need more help? Ask Coddy for instant answers — it's free!

Code B1B00 Description

When powered, the Occupant Restraint Controller (ORC) sends a test current to the squibs to verify the integrity of the squib and wiring. These circuits are maintained in a "floating" configuration at the module (connected to neither power nor ground) as protection against inadvertent deployment. The use of the SRS Load Tool Adaptor provides a test point as well as a method for opening the shorting bar connections within the harness connector. The Clockspring is part of the Steering Column Control Module (SCCM). The SCCM includes the steering column shroud, the Steering Angle Sensor (SAS), the Clockspring, the Multi-function Switch, a Steering Column Power Tilt and Telescope Switch (if equipped), and a trim cover. The SCCM is replaced as an entire assembly. The ORC Module sends out a 40 mA diagnostic current on each squib voltage supply circuit at power up, and every 500 ms thereafter while the ignition is on.

OBDII Code B1B00 - Driver Airbag Squib 1 Circuit Low - AutoCodes.com — B1B00 Code - Driver Airbag Squib 1 Circuit Low

What does this mean?

What are the Possible Causes of the DTC B1B00?

Faulty Driver Airbag Squib 1
Driver Airbag Squib 1 harness is open or shorted
Driver Airbag Squib 1 circuit poor electrical connection
Faulty Driver Airbag
Faulty Steering Comun Control Module (Clockspring)
Faulty Occupant Restraint Controller (ORC)

How to Fix the DTC B1B00?

Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.

What is the Cost to Diagnose the Code?

Labor: 1.0

To diagnose the B1B00 code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.

Need more information about the B1B00 code?

Need more information on how to fix the B1B00 code? Get Access to Factory Service Manuals

Need Help with the Code?

Get the B1B00 code diagnosed by a professional: Find a repair shop in your area

Information for Specific Makes

B1B00 Chrysler — Driver Airbag Squib 1 Circuit Low
B1B00 Dodge — Driver Airbag Squib 1 Circuit Low
B1B00 Jeep — Driver Airbag Squib 1 Circuit Low
B1B00 Mitsubishi — Driver Airbag Squib 1 Circuit Low
B1B00 RAM — Driver Airbag Squib 1 Circuit Low

Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service

Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.

Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.

About the author: William Orellana is a Master Mechanic and Mechanical Engineer with over 30 years of experience diagnosing and repairing vehicles. Learn more about his background.

Frequently Asked Questions about B1B00 Code

1. What are the common symptoms of OBDII code B1B00 (Driver Airbag Squib 1 Circuit Low)?

- The common symptoms include the airbag warning light illuminating on the dashboard and a potential loss of functionality of the driver-side airbag.

2. What are the possible causes of OBDII code B1B00 (Driver Airbag Squib 1 Circuit Low)?

- The code B1B00 can be caused by issues such as a faulty driver airbag squib, damaged wiring or connectors in the airbag system, or a malfunctioning airbag control module.

3. How serious is OBDII code B1B00 (Driver Airbag Squib 1 Circuit Low)?

- This code indicates a potential issue with the driver-side airbag system, which can compromise safety in the event of a collision. It is crucial to address this problem promptly to ensure the proper functioning of the airbag.

4. Can I continue driving with OBDII code B1B00 (Driver Airbag Squib 1 Circuit Low) present?

- It is not recommended to drive with this code active, as it indicates a problem with the driver airbag system. Continuing to drive with a faulty airbag can pose a safety risk in the event of an accident.

5. How can I diagnose OBDII code B1B00 (Driver Airbag Squib 1 Circuit Low)?

- Diagnosis typically involves using an OBDII scanner to read the code, followed by inspecting the driver airbag squib, wiring, connectors, and airbag control module for any visible damage or faults.

6. What are some DIY repair tips for fixing OBDII code B1B00 (Driver Airbag Squib 1 Circuit Low)?

- DIY repair for this code may involve checking and securing the wiring and connectors in the airbag system, and, if necessary, replacing the driver airbag squib or addressing any faults in the airbag control module.

7. Is it safe to reset the OBDII code B1B00 (Driver Airbag Squib 1 Circuit Low) without fixing the underlying issue?

- Resetting the code without addressing the root cause can temporarily clear the warning light but will not fix the underlying problem. It is crucial to diagnose and repair the issue to ensure the proper functioning of the airbag system.

8. Can a mechanic help me fix OBDII code B1B00 (Driver Airbag Squib 1 Circuit Low)?

- Yes, a qualified mechanic can diagnose and repair the issue causing the B1B00 code. They have the tools and expertise to properly inspect and repair the driver airbag system to ensure it functions correctly.

9. Are there any recalls related to OBDII code B1B00 (Driver Airbag Squib 1 Circuit Low)?

- It is advisable to check with the vehicle manufacturer or the National Highway Traffic Safety Administration (NHTSA) for any recalls related to the driver airbag squib or airbag system that could be associated with this code.

10. How much does it typically cost to repair OBDII code B1B00 (Driver Airbag Squib 1 Circuit Low)?

- The cost of repairing the B1B00 code can vary depending on the specific issue causing the fault. Repair costs may include labor charges, replacement parts, and diagnostic fees, so it is recommended to obtain quotes from different mechanics.