U18A2 GMC Code - Lost Communication with Fuel Pump Driver Control Module
Quick Answer
Devices connected to the serial data circuits monitor for serial data communications during normal vehicle operation. Common causes include Faulty Fuel Pump Driver Control Module, Fuel Pump Driver Control Module harness is open or shorted, Fuel Pump Driver Control Module circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- U18A2 GMC indicates Lost Communication with Fuel Pump Driver Control Module.
- Common causes
- Common causes include Faulty Fuel Pump Driver Control Module, Fuel Pump Driver Control Module harness is open or shorted, Fuel Pump Driver Control Module circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code U18A2 GMC Description
What are the Possible Causes of the DTC U18A2 GMC?
- Faulty Fuel Pump Driver Control Module
- Fuel Pump Driver Control Module harness is open or shorted
- Fuel Pump Driver Control Module circuit poor electrical connection
How to Fix the DTC U18A2 GMC?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
Code Tech Notes
- 2014-2018 GMC Sierra
- 2015-2018 GMC Yukon
- 2015-2018 GMC Yukon XL
If the Diagnostic Trouble Codes (DTC) P2635, U0074, and/or U18A2 are set, it may be found that the actual fuel pressure (low-pressure system) will be reading substantially higher than desired fuel pressure, in this case, the cause of the problem is a loss of communication between Engine Control Module (ECM) and Fuel Pump Control Module (FPCM).
- Diagnose for any communication DTCs set (U0074 would take priority over U18A2 if both set) before addressing DTC P2635.
- If DTC P2635 is not resolved by correcting the communication DTCs, only then should diagnose the DTC P2635.
- It has been found that a communication issue between the FPCM and ECM can potentially induce DTC P2635 and result in a pressure differential between actual and desired fuel system pressures.
- If the actual fuel pressure is substantially higher than desired (10 psi / 70 kPa or more), replacement of the fuel pump control module or fuel system components typically will not resolve this issue.
- If the actual fuel pressure is substantially lower than desired (10 psi / 70 kPa or more), this Factory Service Bulletin would NOT apply. It would be recommended to diagnose low actual fuel pressure.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the U18A2 GMC code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the U18A2 GMC code?
Need more information on how to fix the U18A2 GMC code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the U18A2 GMC code diagnosed by a professional: Find a repair shop in your area
Information for Specific GMC Models
- U18A2 2014 GMC Sierra — Lost Communication with Fuel Pump Driver Control Module
- U18A2 2015 GMC Sierra — Lost Communication with Fuel Pump Driver Control Module
- U18A2 2016 GMC Sierra — Lost Communication with Fuel Pump Driver Control Module
- U18A2 2017 GMC Sierra — Lost Communication with Fuel Pump Driver Control Module
- U18A2 2018 GMC Sierra — Lost Communication with Fuel Pump Driver Control Module
Frequently Asked Questions about U18A2 GMC Code
1. What are the common symptoms of OBDII code U18A2 GMC (Lost Communication with Fuel Pump Driver Control Module)?
- Common symptoms include engine stalling, rough idle, difficulty starting the vehicle, and the fuel pump not functioning properly.
2. What are the possible causes of OBDII code U18A2 GMC?
- Possible causes include a faulty fuel pump driver control module, damaged wiring or connectors, a blown fuse, or a problem with the fuel pump itself.
3. How can I diagnose the OBDII code U18A2 GMC issue?
- To diagnose this issue, you can use a diagnostic scanner to retrieve the trouble codes and perform a thorough inspection of the fuel pump driver control module, wiring, connectors, and fuse.
4. What are some repair tips for resolving OBDII code U18A2 GMC?
- Repair tips include checking and replacing any damaged wiring or connectors, testing and replacing the fuel pump driver control module if necessary, and ensuring that the fuse related to the fuel pump is in good condition.
5. Can OBDII code U18A2 GMC be safely driven with?
- It is not recommended to drive the vehicle with this code present, as it can lead to potential issues with fuel delivery and engine performance.
6. How much does it typically cost to repair OBDII code U18A2 GMC?
- The cost of repairing this code can vary depending on the extent of the issue and the specific repairs needed. It is recommended to consult with a mechanic for an accurate estimate.
7. Can I reset the OBDII code U18A2 GMC myself?
- You can attempt to reset the code using an OBDII scanner, but it is important to address the underlying issue causing the code to prevent it from reoccurring.
8. Will disconnecting the battery reset the OBDII code U18A2 GMC?
- Disconnecting the battery may reset the code temporarily, but it is not a guaranteed solution. It is best to diagnose and repair the issue causing the code.
9. How urgent is it to address OBDII code U18A2 GMC?
- It is important to address this code promptly to prevent potential fuel delivery issues and further damage to the vehicle's components.
10. Can a DIY enthusiast repair OBDII code U18A2 GMC at home?
- Depending on the DIY enthusiast's skill level and access to tools, some repairs related to this code, such as checking and replacing fuses or connectors, may be possible at home. However, more complex repairs may require professional assistance.
Discuss the causes and fixes for U18A2 GMC OBDII Code
-
No warning no light went to church on Sunday canyon would not start on Monday. My code reader pulled U18A2
-
Can you share the model and year of your vehicle? This helps in providing specific guidance since U18A2 is a manufacturer-specific code.
Did you notice any unusual behavior before it stopped working? For example, was the vehicle cranking but not starting, or was it completely unresponsive?
U18A2 typically relates to a communication issue between the vehicle's modules. Here are some steps to investigate the issue:
-
Inspect Battery and Connections: Ensure the battery is fully charged and the terminals are clean and secure. Low voltage can trigger communication-related codes.
-
Check for Wiring Issues: Inspect the wiring and connectors leading to the modules. Look for damage, corrosion, or loose connections.
-
Scan All Modules: Use a scanner capable of reading manufacturer-specific codes to check for additional codes in related modules like the ECM, BCM, or TCM.
-
Reset the System: Disconnect the battery for about 10 minutes, then reconnect it. This can reset module communication and clear temporary glitches.
-
-
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
