AutoCodes – Fiat – U11EE Fiat

U11EE Fiat Code - Lost Communication With Right C-Pillar Impact Acceleration Sensor

Quick Answer

The impact sensors perform their own self-test using power supplied by the Occupant Restraint Controller (ORC) then communicate this status back to the ORC with periodic updates. Common causes include Faulty Right C-Pillar Impact Acceleration Sensor, Right C-Pillar Impact Acceleration Sensor harness is open or shorted, Right C-Pillar Impact Acceleration Sensor circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

What it means: U11EE Fiat indicates Lost Communication With Right C-Pillar Impact Acceleration Sensor.
Common causes: Common causes include Faulty Right C-Pillar Impact Acceleration Sensor, Right C-Pillar Impact Acceleration Sensor harness is open or shorted, Right C-Pillar Impact Acceleration Sensor circuit poor electrical connection.
Severity: High - diagnose this code as soon as possible.
Can I drive?: Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

Save to My Repairs My Repairs

AI answers can be wrong. Verify repairs with testing. Open full chat

Code Popularity 558

How popular is this code, among other codes? Low

Repair Importance Level

Urgent (Diagnose now) (3 / 3)

Repair Difficulty Level

Advanced (Pro) (3 / 3)

What is this?

Table of contents Created and updated by William Orellana on May 03, 2020

Description
Possible Causes
How To Fix
Cost to Diagnose
FAQs
Comments
Add Comment

💬 Need more help? Ask Coddy for instant answers — it's free!

Code U11EE Fiat Description

The impact sensors perform their own self-test using power supplied by the Occupant Restraint Controller (ORC) then communicate this status back to the ORC with periodic updates. The repair of this fault condition involves verifying the integrity of the wiring between the ORC and the sensor. This code will set, if the ORC and the Right Side Impact Sensor 2 do not establish and maintain valid data communications. The Diagnostic Trouble Code (DTC) will become active after the fault has set for a minimum of 2.5 seconds. The DTC will go to Stored after the ORC to Right Side Impact Sensor 2 communication fault has been removed or the suspect sensor has been replaced for 2.5 seconds. The Airbag Warning Lamp (AWL) will set in the instrument cluster.

OBDII Code U11EE Fiat - Lost Communication With Right C-Pillar Impact Acceleration Sensor - AutoCodes.com — U11EE Fiat Code - Lost Communication With Right C-Pillar Impact Acceleration Sensor

What does this mean?

What are the Possible Causes of the DTC U11EE Fiat?

Faulty Right C-Pillar Impact Acceleration Sensor
Right C-Pillar Impact Acceleration Sensor harness is open or shorted
Right C-Pillar Impact Acceleration Sensor circuit poor electrical connection
Faulty Occupant Restraint Controller (ORC)

How to Fix the DTC U11EE Fiat?

Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.

What is the Cost to Diagnose the Code?

Labor: 1.0

To diagnose the U11EE Fiat code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.

Need more information about the U11EE Fiat code?

Need more information on how to fix the U11EE Fiat code? Get Access to Factory Service Manuals

Need Help with the Code?

Get the U11EE Fiat code diagnosed by a professional: Find a repair shop in your area

Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service

Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.

Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.

About the author: William Orellana is a Master Mechanic and Mechanical Engineer with over 30 years of experience diagnosing and repairing vehicles. Learn more about his background.

Frequently Asked Questions about U11EE Fiat Code

1. What are the common symptoms of OBDII code U11EE in a Fiat vehicle?

The common symptoms of U11EE code include the airbag warning light illuminating on the dashboard, loss of communication with the right C-pillar impact acceleration sensor, and potential issues with the airbag system.

2. What does the U11EE code mean in a Fiat car?

The U11EE code indicates that there is a communication error with the right C-pillar impact acceleration sensor in the Fiat vehicle, leading to a potential malfunction in the airbag system.

3. What are the possible causes of the U11EE code in a Fiat?

Possible causes of the U11EE code include a faulty C-pillar impact acceleration sensor, damaged wiring or connections related to the sensor, a software glitch, or a problem with the airbag control module.

4. How can I diagnose the U11EE code in my Fiat?

Diagnosing the U11EE code typically involves using a diagnostic scanner to retrieve the fault codes, inspecting the wiring and connections of the right C-pillar impact acceleration sensor, and checking for any physical damage or malfunctions in the sensor itself.

5. Can I drive my Fiat with the U11EE code present?

It is not recommended to drive the vehicle with the U11EE code present, as it indicates a potential issue with the airbag system that may compromise passenger safety in the event of a collision.

6. How can I repair the U11EE code in my Fiat?

Repairing the U11EE code may involve replacing the right C-pillar impact acceleration sensor, repairing any damaged wiring or connections, resetting the airbag system, or reprogramming the airbag control module.

7. Is the U11EE code a serious issue in a Fiat?

Yes, the U11EE code is a serious issue in a Fiat as it indicates a problem with the airbag system, which is a critical safety component of the vehicle designed to protect occupants in the event of a collision.

8. Can I reset the U11EE code in my Fiat without fixing the underlying issue?

While you can clear the U11EE code with a diagnostic scanner, it is essential to address the underlying issue causing the code to prevent potential safety risks and ensure the proper functioning of the airbag system.

9. How much does it cost to fix the U11EE code in a Fiat?

The cost of fixing the U11EE code in a Fiat can vary depending on the specific cause of the issue, the parts needed for repair or replacement, labor costs, and whether you choose to address the problem yourself or take it to a professional mechanic.

10. How can I prevent the U11EE code from reoccurring in my Fiat?

To prevent the U11EE code from reoccurring, it is essential to regularly maintain the airbag system, check for any signs of damage or wear on the impact sensors, wiring, and connections, and address any issues promptly to ensure the safety of the vehicle.