U11EB Jeep Code - Lost Communication With Left C-Pillar Impact Acceleration Sensor
Quick Answer
The impact sensors perform their own self test using power supplied by the Occupant Restraint Controller (ORC) then communicate this status back to the ORC with periodic updates. Common causes include Faulty Left C-Pillar Impact Acceleration Sensor, Left C-Pillar Impact Acceleration Sensor harness is open or shorted, Left C-Pillar Impact Acceleration Sensor circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- U11EB Jeep indicates Lost Communication With Left C-Pillar Impact Acceleration Sensor.
- Common causes
- Common causes include Faulty Left C-Pillar Impact Acceleration Sensor, Left C-Pillar Impact Acceleration Sensor harness is open or shorted, Left C-Pillar Impact Acceleration Sensor circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code U11EB Jeep Description
What are the Possible Causes of the DTC U11EB Jeep?
- Faulty Left C-Pillar Impact Acceleration Sensor
- Left C-Pillar Impact Acceleration Sensor harness is open or shorted
- Left C-Pillar Impact Acceleration Sensor circuit poor electrical connection
- Faulty Occupant Restraint Controller (ORC)
How to Fix the DTC U11EB Jeep?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the U11EB Jeep code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the U11EB Jeep code?
Need more information on how to fix the U11EB Jeep code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the U11EB Jeep code diagnosed by a professional: Find a repair shop in your area
Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service
- Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
- Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
- Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
- Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.
Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.
Frequently Asked Questions about U11EB Jeep Code
What does the OBDII code U11EB mean on a Jeep?
1. The U11EB code indicates a lost communication with the left C-pillar impact acceleration sensor, which is part of the airbag system. 2.
What are common symptoms of the U11EB code in a Jeep?
Symptoms may include the airbag warning light being illuminated, potential deactivation of the airbag system, or no noticeable symptoms at all. 3.
What causes the U11EB code to appear?
The code is typically caused by a faulty left C-pillar impact acceleration sensor, damaged wiring, poor electrical connections, or a malfunctioning control module. 4.
Can I drive my Jeep with the U11EB code active?
While the vehicle may still be drivable, it’s not recommended as the airbag system may be compromised, posing a safety risk in the event of a collision. 5.
How do I diagnose the U11EB code in my Jeep?
Diagnosis involves scanning for stored codes, inspecting the wiring and connectors for damage, and testing the left C-pillar impact acceleration sensor for proper function. 6.
How can I fix the U11EB code on my Jeep?
Repairs may include replacing the left C-pillar impact acceleration sensor, repairing damaged wiring, cleaning corroded connectors, or reprogramming the control module if required. 7.
How much does it cost to fix the U11EB code on a Jeep?
Repair costs vary but typically range from $100 to $300, depending on whether the sensor, wiring, or module needs to be replaced or repaired. 8.
Can a faulty impact sensor trigger other OBDII codes?
Yes, a faulty impact sensor may cause other airbag-related codes, such as those indicating module or system communication issues. 9.
Do I need special tools to troubleshoot the U11EB code?
Yes, a professional OBDII scanner capable of reading manufacturer-specific codes and a multimeter for testing wiring and connections are often required. 10.
Is the U11EB code covered under warranty for my Jeep?
This depends on your vehicle’s warranty coverage and mileage. Airbag components may be covered under specific safety-related warranties, so check with your dealer.
Discuss the causes and fixes for U11EB Jeep OBDII Code
Code U11EB Jeep comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
