P2770 Scion Code - Open in Torque Converter Clutch Solenoid Circuit Shift Solenoid Valve SL
Quick Answer
Shift solenoid valve SL is turned on and off by signals from the Engine Control Module (ECM) to control the hydraulic pressure acting on the lock-up relay valve, which then controls the operation of the lock-up clutch. Common causes include Faulty Torque Converter Clutch Pressure Control Solenoid (Shift Solenoid Valve SLU), Torque Converter Clutch Pressure Control Solenoid harness is open or shorted, Torque Converter Clutch Pressure Control Solenoid circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P2770 Scion indicates Open in Torque Converter Clutch Solenoid Circuit Shift Solenoid Valve SL.
- Common causes
- Common causes include Faulty Torque Converter Clutch Pressure Control Solenoid (Shift Solenoid Valve SLU), Torque Converter Clutch Pressure Control Solenoid harness is open or shorted, Torque Converter Clutch Pressure Control Solenoid circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P2770 Scion Description
Based on the signals from the throttle position sensor, airflow meter, and crankshaft position sensor, the ECM sends a signal to shift solenoid valve SL to regulate the hydraulic pressure and provide smooth torque converter engagement. Shift solenoid valve SL responds to commands from the ECM. The valve controls the lock-up relay valve to perform the torque-converter lock-up function. If the ECM detects an open or short circuit for shift solenoid valve SL, it will illuminate the MIL and store the Diagnostic Trouble Code (DTC).
What are the Possible Causes of the DTC P2770 Scion?
- Faulty Torque Converter Clutch Pressure Control Solenoid (Shift Solenoid Valve SLU)
- Torque Converter Clutch Pressure Control Solenoid harness is open or shorted
- Torque Converter Clutch Pressure Control Solenoid circuit poor electrical connection
- Faulty Engine Control Module (ECM)
How to Fix the DTC P2770 Scion?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P2770 Scion code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P2770 Scion code?
Need more information on how to fix the P2770 Scion code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P2770 Scion code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P2770 Scion Code
What does OBDII code P2770 mean for a Scion?
Code P2770 indicates an open circuit issue in the torque converter clutch solenoid, specifically the shift solenoid valve SL.
What are the symptoms of code P2770?
Common symptoms include transmission slipping, difficulty shifting gears, reduced fuel efficiency, and possible illumination of the check engine light.
What causes code P2770 in a Scion?
Possible causes include a faulty torque converter clutch solenoid, damaged wiring or connectors, transmission fluid issues, or an internal transmission failure.
Can driving with code P2770 damage my Scion?
Yes, driving with this code may cause further transmission damage and reduced performance. It's best to address the issue promptly.
How can I diagnose code P2770?
Start by inspecting the wiring and connectors for damage, check the transmission fluid condition, and test the torque converter clutch solenoid for proper operation.
What tools are needed to fix code P2770?
You’ll typically need a diagnostic scanner, a multimeter for testing electrical connections, and possibly transmission tools if solenoid replacement is required.
How much does it cost to repair code P2770?
Repair costs vary depending on the issue. A solenoid replacement may cost $200-$500, while wiring repairs or fluid changes may cost less.
Does P2770 always mean the solenoid is bad?
No, the issue could be caused by wiring problems, a faulty connector, or even low-quality transmission fluid.
Can I reset code P2770 without fixing the problem?
Clearing the code without fixing the issue may temporarily turn off the check engine light, but the code is likely to return.
Is code P2770 common in Scion vehicles?
While not the most common code, it can occur in Scion vehicles, especially those with higher mileage or transmission wear.
Discuss the causes and fixes for P2770 Scion OBDII Code
Code P2770 Scion comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
