P2767 Jeep Code - Input Speed Sensor 2 Circuit No Signal
Quick Answer
The Input Speed Sensor 2 is one of the two hall effect speed sensors that are used by the Transmission Control Module (TCM) to calculate the transmissions turbine speed. Common causes include Faulty Input Speed Sensor, Input Speed Sensor harness is open or shorted, Input Speed Sensor circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P2767 Jeep indicates Input Speed Sensor 2 Circuit No Signal.
- Common causes
- Common causes include Faulty Input Speed Sensor, Input Speed Sensor harness is open or shorted, Input Speed Sensor circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P2767 Jeep Description
What are the Possible Causes of the DTC P2767 Jeep?
- Faulty Input Speed Sensor
- Input Speed Sensor harness is open or shorted
- Input Speed Sensor circuit poor electrical connection
How to Fix the DTC P2767 Jeep?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P2767 Jeep code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P2767 Jeep code?
Need more information on how to fix the P2767 Jeep code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P2767 Jeep code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P2767 Jeep Code
What does OBD-II code P2767 mean on a Jeep?
Code P2767 indicates that the transmission control module (TCM) has detected no signal from Input Speed Sensor 2, which monitors the rotational speed of specific transmission components.
What are the common symptoms of code P2767 on a Jeep?
Symptoms may include transmission slipping, erratic shifting, poor acceleration, and the Check Engine Light turning on.
What causes code P2767 on a Jeep?
Common causes include a faulty input speed sensor, damaged wiring or connectors, corrosion in the sensor circuit, or a malfunctioning transmission control module (TCM).
Can I drive my Jeep with code P2767?
Driving with this code can lead to poor transmission performance and further damage. It’s best to address the issue promptly to avoid costly repairs.
How do I diagnose code P2767 on a Jeep?
Start by inspecting the input speed sensor, wiring, and connectors for damage or corrosion. Use an OBD-II scanner to monitor sensor data and check for continuity in the circuit.
How do I fix code P2767 on a Jeep?
Repairs may include replacing the input speed sensor, repairing damaged wiring or connectors, cleaning corroded terminals, or updating/replacing the TCM if necessary.
What tools are needed to fix code P2767?
You may need an OBD-II scanner, multimeter, basic hand tools, and replacement parts like the input speed sensor or wiring components.
How much does it cost to repair code P2767 on a Jeep?
Repair costs vary but may range from $100 to $300 for parts and labor, depending on whether the sensor, wiring, or TCM needs replacement.
Can a dirty transmission fluid cause code P2767?
While dirty transmission fluid is not a direct cause, it can contribute to sensor malfunction or poor transmission performance, so checking fluid condition is recommended.
Does code P2767 require professional repair?
While experienced DIYers may handle sensor replacement or wiring repair, complex issues like TCM failure may require professional diagnosis and repair.
Discuss the causes and fixes for P2767 Jeep OBDII Code
-
I appreciate this information - I had the check engine light come on and then the Jeep wouldn't go above 30 miles an hour and was kind of sluggish...I took it to Auto Zone and that was the code they ran. I was looking here to see what the issue might be and I appreciate the detailed information. I don't know if we can fix ourselves, but will look to first before taking to dealership. Thank you!
-
Late response, but what model and year is your Jeep. More than likely you have to take your Jeep to a mechanic to replace the sensor.
-
MINES AN 08 LAREDO THAT WOULDN'T GO ABOVE 55, NO GEARS WOULD CHANGE, BUT AFTER IT SAT FOR 15 MINUTES IT WORKED JUST FINE, WHERE ARE THESE SENSORS LOCATED?
-
Sooo. How did you make out with your 08 Loredo? I have a 2007 that has the same issue. We found that restarting the vehicle is a temporary fix. I appreciate any feedback!
-
It is a 2006 Jeep Grand Cherokee and it tends to get sluggish during summer weather, winter time is great. I turn it off and it's good but sometimes it can start doing the same. There is times I hear a kick. I was given P0700 and P2767. My cousin mentioned to me if catalytic converter could be clogged what do you think thanks
-
I have those same codes any luck on what exactly it could be I been hearing different things
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
