AutoCodes - Honda - P2653 2010 HONDA ACCORD

P2653 2010 HONDA ACCORD Code - Rocker Arm Oil Control Solenoid 'B' Circuit Low Voltage Bank 1

Repair Importance Level: 3/3
Repair Difficulty Level: 3/3
Table of contents

|P2653 2010 HONDA ACCORD code possible causes

  • Check engine oil level, oil condition and pressure
  • Faulty Variable Valve Timing and Lift Electronic Control (VTEC) / Rocker Arm Solenoid Valve
  • VTEC/Rocker Arm Solenoid Valve harness is open or shorted
  • VTEC/Rocker Arm Solenoid Valve circuit poor electrical connection

|How do I fix the P2653 2010 HONDA ACCORD code?

Check the "Possible Causes" listed above. Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector's pins.

|P2653 2010 HONDA ACCORD code tech notes

The most common problem that can set the P2653 code is the engine oil. Before replacing any parts change the engine oil with the factory recommend oil weight.

|Cost of diagnosing the P2653 2010 HONDA ACCORD code

Labor: 1.0

The cost of diagnosing the P2653 2010 HONDA ACCORD code is 1.0 hour of labor. The auto repair's diagnosis time and labor rates vary by location, vehicle's make and model, and even your engine type. Most auto repair shops charge between $75 and $150 per hour.

|When is the P2653 2010 HONDA ACCORD code detected?

When a malfunction is detected during the first drive cycle, a Pending DTC is stored in the Powertrain Control Module (PCM) memory. If the malfunction returns in the next (second) drive cycle, the MIL comes on and a Confirmed DTC and the freeze data are stored.

|What are P2653 2010 HONDA ACCORD code possible symptoms?

  • Engine Light ON (or Service Engine Soon Warning Light)

|P2653 2010 HONDA ACCORD code description

The Variable Valve Timing and Lift Electronic Control (VTEC) system activates the Rocker Arm Oil Control Solenoid (VTEC Solenoid Valve) by command from the Engine Control Module (ECM) / Powertrain Control Module (PCM), and it charges/discharges the hydraulic circuit of the VTEC mechanism that switches valve timing between Low and High. The ECM/PCM monitors oil pressure in the hydraulic circuit of the VTEC mechanism using the rocker arm oil pressure switch (VTEC oil pressure switch) downstream of the rocker arm oil control solenoid (VTEC solenoid valve). If there is a difference between the oil pressure condition in the hydraulic circuit that is determined by the ECM/PCM command and the oil pressure condition that is determined by the status of the rocker arm oil pressure switch (VTEC oil pressure switch), the system is considered faulty, and the Diagnostic Trouble Code (DTC) is stored.
OBDII Code P2653 2010 Honda Accord - Rocker Arm Oil Control Solenoid 'B' Circuit Low Voltage Bank 1 - AutoCodes.com

|Need more information with the P2653 2010 HONDA ACCORD code?

Need more information on how to fix the P2653 2010 HONDA ACCORD code?
Get Access to Factory Service Manuals

|Need help with a P2653 2010 HONDA ACCORD code?

Get the P2653 2010 Honda Accord code diagnosed by a professional: Find a repair shop in your area

|P2653 2010 HONDA ACCORD code comments

Help us improve AutoCodes.com. Leave a comment below or tell us if the information above helps you fix the code. What are the symptoms on your vehicle for the P2653 2010 Honda Accord code? Have you replaced any parts?
Any information is appreciated. Thanks
Top ⇧
Repair Importance Level: 3
 
1=Low 2=Medium 3=High What is this?
Repair Difficulty Level: 3
 
1=Easy 2=Moderate 3=Hard What is this?