P2619 2018 GMC Sierra Code - Crankshaft Position Signal Output Circuit High Voltage
Quick Answer
The Crankshaft Position Sensor is also known as the crank position sensor is an electronic device used in an engine to record the rate at which the crankshaft is spinning. Common causes include Faulty Crankshaft Position Sensor, Crankshaft Position Sensor harness is open or shorted, Crankshaft Position Sensor circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P2619 2018 GMC Sierra indicates Crankshaft Position Signal Output Circuit High Voltage.
- Common causes
- Common causes include Faulty Crankshaft Position Sensor, Crankshaft Position Sensor harness is open or shorted, Crankshaft Position Sensor circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P2619 2018 GMC Sierra Description
When the engine is running, the high and low parts of the teeth cause the gap with the sensor to change. The changing gap causes the magnetic field near the sensor to change. The change in the magnetic field causes the voltage from the sensor to change.
The Diagnostic Trouble Code (DTC) will be set when the Crankshaft Position Signal Output Circuit is short to voltage for greater than 5 s.
What are the Possible Causes of the DTC P2619 2018 GMC Sierra?
- Faulty Crankshaft Position Sensor
- Crankshaft Position Sensor harness is open or shorted
- Crankshaft Position Sensor circuit poor electrical connection
How to Fix the DTC P2619 2018 GMC Sierra?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P2619 2018 GMC Sierra code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P2619 2018 GMC Sierra code?
Need more information on how to fix the P2619 2018 GMC Sierra code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P2619 2018 GMC Sierra code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P2619 2018 GMC Sierra Code
1. What are the common symptoms of OBDII code P2619 in a 2018 GMC Sierra?
The common symptoms of OBDII code P2619 in a 2018 GMC Sierra include rough idling, engine stalling, poor acceleration, and in some cases, the vehicle may not start.
2. What does the OBDII code P2619 indicate in a 2018 GMC Sierra?
OBDII code P2619 in a 2018 GMC Sierra indicates a high voltage condition in the crankshaft position signal output circuit.
3. What are the possible causes of OBDII code P2619 in a 2018 GMC Sierra?
The possible causes of OBDII code P2619 in a 2018 GMC Sierra include a faulty crankshaft position sensor, damaged wiring or connectors in the circuit, a defective engine control module (ECM), or a problem with the crankshaft itself.
4. How can I diagnose the OBDII code P2619 in my 2018 GMC Sierra?
Diagnosing OBDII code P2619 in a 2018 GMC Sierra involves checking the crankshaft position sensor for proper operation, inspecting the wiring and connectors for damage, testing the ECM, and ensuring the crankshaft is functioning correctly.
5. Is it safe to drive my 2018 GMC Sierra with OBDII code P2619?
It is not recommended to drive your 2018 GMC Sierra with OBDII code P2619, as the high voltage condition in the crankshaft position signal output circuit can cause engine performance issues and potential damage if left unresolved.
6. Can I reset the OBDII code P2619 in my 2018 GMC Sierra by disconnecting the battery?
While disconnecting the battery may temporarily clear the code, it is important to diagnose and repair the underlying issue causing OBDII code P2619 in your 2018 GMC Sierra to prevent it from returning.
7. How much does it cost to repair OBDII code P2619 in a 2018 GMC Sierra?
The cost to repair OBDII code P2619 in a 2018 GMC Sierra can vary depending on the cause of the issue, but it may involve replacing the crankshaft position sensor, repairing wiring or connectors, or addressing ECM problems, which could range from relatively inexpensive to more costly repairs.
8. Can a DIY enthusiast fix OBDII code P2619 in a 2018 GMC Sierra?
A DIY enthusiast may be able to fix OBDII code P2619 in a 2018 GMC Sierra if they have the necessary tools, knowledge, and experience to diagnose and repair issues related to the crankshaft position signal output circuit.
9. Will OBDII code P2619 cause my 2018 GMC Sierra to fail an emissions test?
OBDII code P2619 can potentially cause your 2018 GMC Sierra to fail an emissions test, as it indicates a problem with the crankshaft position signal output circuit, which can impact engine performance and emissions control.
10. How long does it typically take to repair OBDII code P2619 in a 2018 GMC Sierra?
The time it takes to repair OBDII code P2619 in a 2018 GMC Sierra can vary depending on the cause of the issue and the complexity of the repair needed, but it may take a few hours to a full day to diagnose and fix the problem.
Discuss the causes and fixes for P2619 2018 GMC Sierra OBDII Code
Code P2619 2018 GMC Sierra comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
