P2619 2016 GMC Sierra Code - Crankshaft Position Signal Output Circuit High Voltage
Quick Answer
The Crankshaft Position Sensor is also known as the crank position sensor is an electronic device used in an engine to record the rate at which the crankshaft is spinning. Common causes include Faulty Crankshaft Position Sensor, Crankshaft Position Sensor harness is open or shorted, Crankshaft Position Sensor circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P2619 2016 GMC Sierra indicates Crankshaft Position Signal Output Circuit High Voltage.
- Common causes
- Common causes include Faulty Crankshaft Position Sensor, Crankshaft Position Sensor harness is open or shorted, Crankshaft Position Sensor circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P2619 2016 GMC Sierra Description
When the engine is running, the high and low parts of the teeth cause the gap with the sensor to change. The changing gap causes the magnetic field near the sensor to change. The change in the magnetic field causes the voltage from the sensor to change.
The Diagnostic Trouble Code (DTC) will be set when the Crankshaft Position Signal Output Circuit is short to voltage for greater than 5 s.
What are the Possible Causes of the DTC P2619 2016 GMC Sierra?
- Faulty Crankshaft Position Sensor
- Crankshaft Position Sensor harness is open or shorted
- Crankshaft Position Sensor circuit poor electrical connection
How to Fix the DTC P2619 2016 GMC Sierra?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P2619 2016 GMC Sierra code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P2619 2016 GMC Sierra code?
Need more information on how to fix the P2619 2016 GMC Sierra code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P2619 2016 GMC Sierra code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P2619 2016 GMC Sierra Code
1. What are the common symptoms of OBDII code P2619 in a 2016 GMC Sierra?
The common symptoms of code P2619 include rough idling, stalling, difficulty starting the engine, and reduced engine performance.
2. What causes the OBDII code P2619 in a 2016 GMC Sierra?
The code P2619 is triggered when the Engine Control Module (ECM) detects a high voltage condition in the crankshaft position signal output circuit. This can be caused by a faulty crankshaft position sensor, damaged wiring, or a malfunctioning ECM.
3. How can I diagnose the OBDII code P2619 in my 2016 GMC Sierra?
Diagnosing code P2619 involves checking the crankshaft position sensor and its wiring for any damage or loose connections. It is also recommended to perform a thorough inspection of the ECM and its connectors for any signs of malfunction.
4. Can I drive my 2016 GMC Sierra with OBDII code P2619?
It is not recommended to drive your vehicle with code P2619 as it can lead to further engine damage and potential safety hazards. It is advised to address the issue promptly to avoid any complications.
5. How do I repair OBDII code P2619 in my 2016 GMC Sierra?
To repair code P2619, you may need to replace the faulty crankshaft position sensor, repair any damaged wiring, or reprogram the ECM if necessary. It is recommended to consult a professional mechanic for accurate diagnosis and repair.
6. Is it safe to clear the OBDII code P2619 in my 2016 GMC Sierra using a diagnostic tool?
Clearing the code using a diagnostic tool may temporarily turn off the Check Engine Light, but it will not fix the underlying issue causing code P2619. It is essential to address the root cause of the problem to prevent the code from reoccurring.
7. How much does it cost to fix OBDII code P2619 in a 2016 GMC Sierra?
The cost of fixing code P2619 can vary depending on the cause of the issue, the replacement parts needed, and labor costs. It is recommended to obtain quotes from different repair shops to compare prices.
8. Can a DIY enthusiast repair OBDII code P2619 in a 2016 GMC Sierra?
While some DIY enthusiasts may be able to diagnose and repair code P2619, it is a complex issue that may require specialized tools and expertise. It is advisable to seek professional help to ensure the problem is addressed correctly.
9. Will OBDII code P2619 cause my 2016 GMC Sierra to fail an emissions test?
Yes, code P2619 can cause your vehicle to fail an emissions test as it indicates a malfunction in the crankshaft position signal output circuit, which can affect the engine's performance and emissions.
10. How often does OBDII code P2619 occur in a 2016 GMC Sierra?
Code P2619 is not a common OBDII code, but it can occur in a 2016 GMC Sierra due to various factors such as sensor failure, wiring issues, or ECM malfunctions. Regular maintenance and timely repairs can help prevent this code from appearing.
Discuss the causes and fixes for P2619 2016 GMC Sierra OBDII Code
Code P2619 2016 GMC Sierra comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
