P258F Dodge Code - Torque Management Request Output Signal
Quick Answer
To improve shift feel, the Transmission Control Module (TCM) may request that the Engine Control Module (ECM) reduce engine torque during shift events. Common causes include Faulty Engine Control Module (ECM), Faulty Transmission Control Module (TCM), Engine Control Module (ECM) software update. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P258F Dodge indicates Torque Management Request Output Signal.
- Common causes
- Common causes include Faulty Engine Control Module (ECM), Faulty Transmission Control Module (TCM), Engine Control Module (ECM) software update.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P258F Dodge Description
The torque reduction request is sent to the ECM through a communication network called the controller area network (CAN). Two circuits are used to communicate CAN data between the ECM and TCM.
A fault in the CAN will not cause the ECM to set the Diagnostic Trouble Codes (DTC). If a CAN fault occurs, other DTCs will set before this code.
The ECM set the OBDII code when the TCM receives a torque reduction failure message from the ECM.
What are the Possible Causes of the DTC P258F Dodge?
- Faulty Engine Control Module (ECM)
- Faulty Transmission Control Module (TCM)
- Engine Control Module (ECM) software update
- Transmission Control Module (TCM) software update
- Engine Control Module (ECM) harness is open or shorted
- Engine Control Module (ECM) circuit poor electrical connection
How to Fix the DTC P258F Dodge?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P258F Dodge code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P258F Dodge code?
Need more information on how to fix the P258F Dodge code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P258F Dodge code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P258F Dodge Code
1. What are the common symptoms of OBDII code P258F (Dodge) related to Torque Management Request Output Signal?
The common symptoms include reduced engine power, hesitation during acceleration, and illuminated Check Engine Light.
2. What typically causes the OBDII code P258F (Dodge) indicating an issue with Torque Management Request Output Signal?
The code is often triggered by a faulty torque management request output signal sensor, damaged wiring or connectors, or a problem with the engine control module (ECM).
3. How can I diagnose the OBDII code P258F (Dodge) related to Torque Management Request Output Signal?
Diagnosis involves using a scan tool to retrieve the code, testing the torque management request output signal sensor, inspecting the wiring for damage, and checking the ECM for any faults.
4. What are the recommended repair tips for fixing OBDII code P258F (Dodge) involving Torque Management Request Output Signal?
Repair tips may include replacing the torque management request output signal sensor, repairing or replacing damaged wiring or connectors, and reprogramming or replacing the ECM if necessary.
5. Can driving with the OBDII code P258F (Dodge) indicating an issue with Torque Management Request Output Signal cause further damage?
Continued driving with this code may lead to reduced engine performance and potential damage to other components, so it is advisable to address the issue promptly.
6. How do I reset the Check Engine Light after repairing the OBDII code P258F (Dodge) linked to Torque Management Request Output Signal?
You can reset the Check Engine Light using a scan tool or by disconnecting the car's battery for a few minutes, then reconnecting it to clear the code.
7. Are there any recalls or technical service bulletins (TSBs) related to OBDII code P258F (Dodge) regarding Torque Management Request Output Signal?
It's recommended to check with Dodge dealerships or online resources for any recalls or TSBs specifically addressing issues related to this OBDII code.
8. How urgent is it to address the OBDII code P258F (Dodge) associated with Torque Management Request Output Signal?
While the severity may vary, addressing this code promptly is crucial to prevent potential engine performance issues and further damage to components.
9. Can a DIY enthusiast with basic automotive knowledge fix the OBDII code P258F (Dodge) related to Torque Management Request Output Signal?
Depending on the exact cause, some repairs related to this code may be within reach for a DIY enthusiast with basic automotive knowledge, but complex issues may require professional assistance.
10. How can I prevent the recurrence of OBDII code P258F (Dodge) concerning Torque Management Request Output Signal in the future?
Regular maintenance, timely repairs of any related issues, and ensuring proper care of engine components can help prevent the recurrence of this OBDII code in the future.
Discuss the causes and fixes for P258F Dodge OBDII Code
Code P258F Dodge comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
