P2422 Acura Code - Evaporative Emission System Vent Valve Stuck Closed
Quick Answer
The fuel tank pressure (FTP) sensor output indicates about atmospheric pressure 0 kPa (0 in.Hg, 0 mmHg) before purge starts since the evaporative emission (EVAP) canister vent shut valve is normally open (open to the atmosphere). Common causes include Faulty Evaporative Emission Vent Shut Valve, Evaporative Emission Vent Shut Valve harness is open or shorted, Evaporative Emission Vent Shut Valve circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P2422 Acura indicates Evaporative Emission System Vent Valve Stuck Closed.
- Common causes
- Common causes include Faulty Evaporative Emission Vent Shut Valve, Evaporative Emission Vent Shut Valve harness is open or shorted, Evaporative Emission Vent Shut Valve circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P2422 Acura Description
When the FTP sensor indicates vacuum after starting the engine, there is the possibility of an FTP sensor zero point shift failure or an EVAP canister vent shut valve stuck closed failure. So the Powertrain Control Module (PCM) monitors the FTP sensor output after purge starts. The PCM detects a malfunction of the EVAP canister vent shut valve if the output indicates excessive vacuum.
However, if the fuel tank internal pressure is below the specified value (excessive vacuum is detected) when starting the engine, the malfunction detection should be done as follows because it is difficult to distinguish the FTP sensor range problem (P1454) from the EVAP canister vent shut valve stuck closed (P2422).
1. If neither Temporary Diagnostic Trouble Code (DTC) (P1454 nor P2422) is stored, both DTCs are stored.
2. If both Temporary DTCs (P1454 and P2422) are stored and excessive vacuum is detected, both DTCs are stored.
3. If either Temporary DTC (P1454 or P2422) is stored and excessive vacuum is detected, the PCM stores the DTC of the Temporary DTC that was stored.
What are the Possible Causes of the DTC P2422 Acura?
- Faulty Evaporative Emission Vent Shut Valve
- Evaporative Emission Vent Shut Valve harness is open or shorted
- Evaporative Emission Vent Shut Valve circuit poor electrical connection
How to Fix the DTC P2422 Acura?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P2422 Acura code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P2422 Acura code?
Need more information on how to fix the P2422 Acura code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P2422 Acura code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P2422 Acura Code
1. What does OBDII code P2422 mean on an Acura?
P2422 indicates that the evaporative emission (EVAP) system vent valve is stuck closed, preventing proper venting of fuel vapors from the EVAP system.
2. What are the common symptoms of code P2422 on an Acura?
You may notice a check engine light, difficulty refueling due to pressure buildup, a slight drop in fuel efficiency, or a failed emissions test.
3. What causes the P2422 code to appear on an Acura?
Common causes include a faulty EVAP vent valve, clogged vent lines, electrical issues such as damaged wiring or connectors, or a problem with the EVAP system pressure sensor.
4. Can I drive my Acura with the P2422 code?
While the car may still be drivable, it's not recommended to ignore the issue as it can affect emissions and may lead to further damage over time.
5. How do I fix the P2422 code on my Acura?
Repairs typically involve inspecting and replacing a stuck or faulty EVAP vent valve, cleaning clogged vent lines, or repairing damaged wiring in the vent valve circuit.
6. How much does it cost to repair the P2422 code on an Acura?
The cost can range from $150 to $400, depending on whether the EVAP vent valve needs replacement or if additional repairs are required.
7. How can I diagnose the P2422 code on my Acura?
Use an OBDII scanner to confirm the code, then inspect the EVAP vent valve for physical damage or clogs. Check the wiring and connectors for continuity or corrosion.
8. Can a loose gas cap cause the P2422 code on an Acura?
No, a loose gas cap is more likely to trigger a different EVAP-related code, such as P0455 or P0456. P2422 specifically relates to the vent valve being stuck closed.
9. What tools are needed to fix the P2422 code on an Acura?
You may need an OBDII scanner, multimeter, basic hand tools, and possibly a vacuum pump to test the EVAP system components.
10. Does the P2422 code affect emissions testing?
Yes, the P2422 code will likely cause your Acura to fail an emissions test since the EVAP system is not functioning properly.
Discuss the causes and fixes for P2422 Acura OBDII Code
Code P2422 Acura comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
