AutoCodes – Toyota – P2402 2015 Toyota RAV4

P2402 2015 Toyota RAV4 Code - Evaporative Emission Leak Detection Pump Stuck ON

Quick Answer

5 hours after the ignition switch is turned off, the leak detection pump creates negative pressure (vacuum) in the Evaporative Emission (EVAP) system. Common causes include Faulty Canister Pump Module, Canister Pump Module harness is open or shorted, Canister Pump Module circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

What it means: P2402 2015 Toyota RAV4 indicates Evaporative Emission Leak Detection Pump Stuck ON.
Common causes: Common causes include Faulty Canister Pump Module, Canister Pump Module harness is open or shorted, Canister Pump Module circuit poor electrical connection.
Severity: High - diagnose this code as soon as possible.
Can I drive?: Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

Save to My Repairs My Repairs

AI answers can be wrong. Verify repairs with testing. Open full chat

Code Popularity 466

How popular is this code, among other codes? Low

Repair Importance Level

Urgent (Diagnose now) (3 / 3)

Repair Difficulty Level

Advanced (Pro) (3 / 3)

What is this?

Table of contents Created and updated by William Orellana on Aug 30, 2022

Description
Possible Causes
How To Fix
Cost to Diagnose
FAQs
Comments
Add Comment

💬 Need more help? Ask Coddy for instant answers — it's free!

Code P2402 2015 Toyota RAV4 Description

5 hours after the ignition switch is turned off, the leak detection pump creates negative pressure (vacuum) in the Evaporative Emission (EVAP) system. The Engine Control Module (ECM) monitors for leaks and actuator malfunctions based on the EVAP pressure. The leak detection pump creates negative pressure through the reference orifice. When the system is normal, the EVAP pressure is between 97 to 100 kPa(abs) [726 to 750 mmHg(abs) (Typical value)] and saturated within a minute. If not, the ECM interprets this as a malfunction. The ECM illuminates the MIL and stores a Diagnostic Trouble Code (DTC) if this malfunction is detected in consecutive drive cycles. The Canister Pump Module is attached to the EVAP Canister and contains the Canister Pressure Sensor, the Leak Detection Pump, and the Vent Valve.

OBDII Code P2402 2015 Toyota RAV4 - Evaporative Emission Leak Detection Pump Stuck ON - AutoCodes.com — P2402 2015 Toyota RAV4 Code - Evaporative Emission Leak Detection Pump Stuck ON

What does this mean?

What are the Possible Causes of the DTC P2402 2015 Toyota RAV4?

Faulty Canister Pump Module
Canister Pump Module harness is open or shorted
Canister Pump Module circuit poor electrical connection
Faulty Engine Control Module (ECM)

How to Fix the DTC P2402 2015 Toyota RAV4?

Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.

What is the Cost to Diagnose the Code?

Labor: 1.0

To diagnose the P2402 2015 Toyota RAV4 code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.

Need more information about the P2402 2015 Toyota RAV4 code?

Need more information on how to fix the P2402 2015 Toyota RAV4 code? Get Access to Factory Service Manuals

Need Help with the Code?

Get the P2402 2015 Toyota RAV4 code diagnosed by a professional: Find a repair shop in your area

About the author: William Orellana is a Master Mechanic and Mechanical Engineer with over 30 years of experience diagnosing and repairing vehicles. Learn more about his background.

Frequently Asked Questions about P2402 2015 Toyota RAV4 Code

1. What does OBDII code P2402 in a 2015 Toyota RAV4 mean?

Code P2402 indicates a problem with the Evaporative Emission Leak Detection Pump being stuck ON.

2. What are the common symptoms of OBDII code P2402 in a 2015 Toyota RAV4?

Common symptoms include the check engine light coming on, decreased fuel efficiency, and potential fuel odors.

3. What can cause the Evaporative Emission Leak Detection Pump to be stuck ON in a 2015 Toyota RAV4?

Potential causes include a faulty leak detection pump, damaged wiring, a vacuum leak, or a malfunctioning purge valve.

4. How serious is OBDII code P2402 in a 2015 Toyota RAV4?

While the vehicle may still be operable, it is important to address this issue promptly to prevent further damage to the emission control system and ensure optimal performance.

5. Can OBDII code P2402 in a 2015 Toyota RAV4 be fixed at home?

Depending on the cause, some DIY enthusiasts may be able to address this issue by replacing the leak detection pump, checking and repairing any damaged wiring, or fixing vacuum leaks.

6. How much does it typically cost to repair OBDII code P2402 in a 2015 Toyota RAV4?

The cost of repair can vary depending on the root cause of the issue, but it may range from $200 to $500 at a repair shop.

7. Will driving with OBDII code P2402 in a 2015 Toyota RAV4 cause further damage?

Continued driving with this issue may lead to decreased fuel efficiency, increased emissions, and potential damage to other emission control components.

8. How can I prevent OBDII code P2402 from appearing in my 2015 Toyota RAV4?

Regular vehicle maintenance, including checking and replacing the evaporative emission system components as recommended, can help prevent this code from appearing.

9. Can clearing the OBDII code P2402 in a 2015 Toyota RAV4 temporarily resolve the issue?

Clearing the code may temporarily turn off the check engine light, but if the underlying problem is not addressed, the code is likely to reappear.

10. Is it safe to drive my 2015 Toyota RAV4 with OBDII code P2402?

While the vehicle may still be safe to drive, it is recommended to have the issue diagnosed and repaired as soon as possible to ensure proper functioning of the emission control system.