AutoCodes – Chevrolet – P2202 Chevrolet

P2202 Chevrolet Code - NOx Sensor 1 Circuit Low Voltage

Quick Answer

The Nitrogen Oxides (NOx) sensors are part of the selective catalytic reduction system, a device used to reduce NOx emission on diesel engines. Common causes include Faulty Nitrogen Oxides (NOx) Sensor, Nitrogen Oxides Sensor harness is open or shorted, Nitrogen Oxides Sensor circuit poor electrical connection. Severity is Moderate - service should be scheduled soon. The vehicle may still be drivable for short trips if it runs normally, but avoid hard driving and repair it soon.

What it means: P2202 Chevrolet indicates NOx Sensor 1 Circuit Low Voltage.
Common causes: Common causes include Faulty Nitrogen Oxides (NOx) Sensor, Nitrogen Oxides Sensor harness is open or shorted, Nitrogen Oxides Sensor circuit poor electrical connection.
Severity: Moderate - service should be scheduled soon.
Can I drive?: The vehicle may still be drivable for short trips if it runs normally, but avoid hard driving and repair it soon.

Save to My Repairs My Repairs

AI answers can be wrong. Verify repairs with testing. Open full chat

Code Popularity 5,522

How popular is this code, among other codes? Low

Repair Importance Level

Moderate (Service soon) (2 / 3)

Repair Difficulty Level

Intermediate (2 / 3)

What is this?

Table of contents Created and updated by William Orellana on Mar 29, 2024

Description
Possible Causes
How To Fix
Tech Notes
Cost to Diagnose
Comments
Add Comment

💬 Need more help? Ask Coddy for instant answers — it's free!

Code P2202 Chevrolet Description

The Nitrogen Oxides (NOx) sensors are part of the selective catalytic reduction system, a device used to reduce NOx emission on diesel engines. There are two NOx sensors, one placed upstream of selective catalytic reduction, to measure inlet NOx concentration, and one placed downstream. They are connected with the control module via CAN and all the information is exchanged through it. Since it is a smart sensor, all the electrical monitoring is performed inside the sensor and only the results are sent to the Engine Control Module (ECM). Each NOx sensor contains a sensing cell, a pumping cell, and a heater. A sample of exhaust gas passes through a diffusion gap between the sensing cell and the pumping cell. The NOx sensor maintains a constant reference voltage across the sensing cell. An electronic circuit within the sensor controls the pump current through the pumping cell in order to maintain a constant voltage in the sensing cell. The amount of current required to maintain the reference voltage in the sensing cell is proportional to the concentration of NOx in the exhaust. The ECM varies the amount of diesel exhaust fluid (reductant) added by varying the reductant injector duty cycle in response to changes in engine exhaust NOx levels. The smart NOx sensors consist of two components, the NOx module and the NOx sensor element that are serviced as a unit. A circuit or performance condition with a NOx sensor is detected by the NOx sensor module. The smart NOx sensor module communicates the condition to the ECM over the serial data line. The ECM sets a DTC when a serial data message is received from the NOx sensor module. The Diagnostic Trouble Code (DTC) will be set if the ECM software detects a fault in the NOx sensor circuitry or a performance fault in the NOx sensor for greater than 2 s.

OBDII Code P2202 Chevrolet - NOx Sensor 1 Circuit Low Voltage - AutoCodes.com — P2202 Chevrolet Code - NOx Sensor 1 Circuit Low Voltage

What does this mean?

What are the Possible Causes of the DTC P2202 Chevrolet?

Faulty Nitrogen Oxides (NOx) Sensor
Nitrogen Oxides Sensor harness is open or shorted
Nitrogen Oxides Sensor circuit poor electrical connection

How to Fix the DTC P2202 Chevrolet?

Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.

What does this mean?

Code Tech Notes

There is a Factory Service Bulletin for the following Chevrolet models:
2010 Chevrolet Express
2011 Chevrolet Express
2011 Chevrolet Silverado
Chevrolet Factory Service Bulletin OBDII Code P2202

What is the Cost to Diagnose the Code?

Labor: 1.0

To diagnose the P2202 Chevrolet code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.

Need more information about the P2202 Chevrolet code?

Need more information on how to fix the P2202 Chevrolet code? Get Access to Factory Service Manuals

Need Help with the Code?

Get the P2202 Chevrolet code diagnosed by a professional: Find a repair shop in your area

Information for Specific Chevrolet Models

P2202 2014 Chevrolet Silverado — NOx Sensor 1 Circuit Low Voltage
P2202 2015 Chevrolet Silverado — NOx Sensor 1 Circuit Low Voltage
P2202 2016 Chevrolet Silverado — NOx Sensor 1 Circuit Low Voltage
P2202 2017 Chevrolet Silverado — NOx Sensor 1 Circuit Low Voltage
P2202 2018 Chevrolet Silverado — NOx Sensor 1 Circuit Low Voltage

About the author: William Orellana is a Master Mechanic and Mechanical Engineer with over 30 years of experience diagnosing and repairing vehicles. Learn more about his background.