AutoCodes – GMC – P2176 GMC

P2176 GMC Code - Minimum Throttle Position Not Learned

Quick Answer

The Engine Control Module (ECM) determines the driver's intent based on input from the accelerator pedal position sensors, then calculates the appropriate throttle response based on the throttle position sensors. Common causes include Binding or bent Throttle Plate, Faulty Throttle Body Assembly, Throttle Body Assembly harness is open or shorted. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

What it means: P2176 GMC indicates Minimum Throttle Position Not Learned.
Common causes: Common causes include Binding or bent Throttle Plate, Faulty Throttle Body Assembly, Throttle Body Assembly harness is open or shorted.
Severity: High - diagnose this code as soon as possible.
Can I drive?: Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

Save to My Repairs My Repairs

AI answers can be wrong. Verify repairs with testing. Open full chat

Code Popularity 17,442

How popular is this code, among other codes? Low

Repair Importance Level

Urgent (Diagnose now) (3 / 3)

Repair Difficulty Level

Intermediate (2 / 3)

What is this?

Table of contents Created and updated by William Orellana on Aug 13, 2022

Description
Possible Causes
How To Fix
Tech Notes
Cost to Diagnose
Comments
Add Comment

💬 Need more help? Ask Coddy for instant answers — it's free!

Code P2176 GMC Description

The Engine Control Module (ECM) determines the driver's intent based on input from the accelerator pedal position sensors, then calculates the appropriate throttle response based on the throttle position sensors. The ECM controls the throttle valve by applying a varying voltage to the control circuits of the Throttle Actuator Control (TAC) motor. The ECM monitors the duty cycle that is required to actuate the throttle valve. The ECM monitors the TP sensor signal/serial data circuit to determine the actual throttle valve position. The TP sensor information is transmitted between the throttle body and the ECM on the signal/serial data circuit. The Diagnostic Trouble Code (DTC) will be set when the ECM detects that both throttle position (TP) sensors were greater than a predetermined voltage during the minimum throttle learn the procedure for greater than 2 s.

OBDII Code P2176 GMC - Minimum Throttle Position Not Learned - AutoCodes.com — P2176 GMC Code - Minimum Throttle Position Not Learned

What does this mean?

What are the Possible Causes of the DTC P2176 GMC?

Binding or bent Throttle Plate
Faulty Throttle Body Assembly
Throttle Body Assembly harness is open or shorted
Throttle Body Assembly circuit poor electrical connection
Faulty Engine Control Module (ECM)

How to Fix the DTC P2176 GMC?

Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.

What does this mean?

Code Tech Notes

There is a factory service bulletin for the P2176 code on the following GMC vehicles:

2004-2012 GMC Canyon
2002-2009 GMC Envoy
GMC Canyon, Envoy Factory Service Bulletin OBDII Code P2176

What is the Cost to Diagnose the Code?

Labor: 1.0

To diagnose the P2176 GMC code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.

Need more information about the P2176 GMC code?

Need more information on how to fix the P2176 GMC code? Get Access to Factory Service Manuals

Need Help with the Code?

Get the P2176 GMC code diagnosed by a professional: Find a repair shop in your area

Information for Specific GMC Models

P2176 2014 GMC Sierra — Minimum Throttle Position Not Learned
P2176 2015 GMC Sierra — Minimum Throttle Position Not Learned
P2176 2016 GMC Sierra — Minimum Throttle Position Not Learned
P2176 2017 GMC Sierra — Minimum Throttle Position Not Learned
P2176 2018 GMC Sierra — Minimum Throttle Position Not Learned

About the author: William Orellana is a Master Mechanic and Mechanical Engineer with over 30 years of experience diagnosing and repairing vehicles. Learn more about his background.