P2138 2010 Nissan Rogue Code - Accelerator Pedal Position Sensor Circuit Range/Performance
Quick Answer
The Accelerator Pedal Position (APP) sensor is installed on the upper end of the accelerator pedal assembly. Common causes include Faulty Accelerator Pedal Position Sensor, Accelerator Pedal Position Sensor harness is open or shorted, Accelerator Pedal Position Sensor circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P2138 2010 Nissan Rogue indicates Accelerator Pedal Position Sensor Circuit Range/Performance.
- Common causes
- Common causes include Faulty Accelerator Pedal Position Sensor, Accelerator Pedal Position Sensor harness is open or shorted, Accelerator Pedal Position Sensor circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P2138 2010 Nissan Rogue Description
Accelerator pedal position sensor has two sensors. These sensors are a kind of potentiometers which transform the accelerator pedal position into output voltage, and emit the voltage signal to the ECM.
In addition, these sensors detect the opening and closing speed of the accelerator pedal and feed the voltage signals to the ECM. The ECM judges the current opening angle of the accelerator pedal from these signals and controls the throttle control motor based on these signals.
Idle position of the accelerator pedal is determined by the ECM receiving the signal from the accelerator pedal position sensor. The ECM uses this signal for the engine operation
such as fuel cut.
What are the Possible Causes of the DTC P2138 2010 Nissan Rogue?
- Faulty Accelerator Pedal Position Sensor
- Accelerator Pedal Position Sensor harness is open or shorted
- Accelerator Pedal Position Sensor circuit poor electrical connection
- Faulty Electric Throttle Control Actuator
- Crankshaft position sensor (POS)
- Refrigerant pressure sensor
- EVAP control system pressure sensor
How to Fix the DTC P2138 2010 Nissan Rogue?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P2138 2010 Nissan Rogue code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P2138 2010 Nissan Rogue code?
Need more information on how to fix the P2138 2010 Nissan Rogue code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P2138 2010 Nissan Rogue code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P2138 2010 Nissan Rogue Code
1. What are the common symptoms of OBDII code P2138 in a 2010 Nissan Rogue?
- Common symptoms include reduced engine power, hesitation or stalling during acceleration, and the vehicle going into "limp mode."
2. What does OBDII code P2138 on a 2010 Nissan Rogue indicate?
- OBDII code P2138 indicates an issue with the Accelerator Pedal Position Sensor Circuit Range/Performance in the vehicle.
3. What are the possible causes of OBDII code P2138 in a 2010 Nissan Rogue?
- Possible causes include a faulty accelerator pedal position sensor, damaged wiring or connectors in the sensor circuit, or issues with the engine control module (ECM).
4. How can I diagnose the cause of OBDII code P2138 in my 2010 Nissan Rogue?
- Diagnosis involves using a scan tool to read the code, checking the accelerator pedal position sensor's voltage readings, and inspecting the wiring and connectors for any damage.
5. Can I still drive my 2010 Nissan Rogue with OBDII code P2138?
- It is not recommended to drive the vehicle with OBDII code P2138 as it can lead to unsafe driving conditions and potential further damage to the vehicle.
6. How can I repair OBDII code P2138 in my 2010 Nissan Rogue?
- Repairing OBDII code P2138 may involve replacing the accelerator pedal position sensor, repairing damaged wiring or connectors, or reprogramming the engine control module (ECM).
7. Will resetting the OBDII code P2138 in my 2010 Nissan Rogue make it go away permanently?
- Resetting the code may temporarily clear the warning light, but if the underlying issue causing the code is not addressed, it is likely to reappear.
8. Is it safe to continue driving if the OBDII code P2138 warning light is intermittent in my 2010 Nissan Rogue?
- It is not recommended to continue driving the vehicle if the warning light is intermittent, as the issue causing the code may worsen and lead to potential safety hazards.
9. Can a DIY mechanic fix OBDII code P2138 in a 2010 Nissan Rogue?
- While some aspects of diagnosing and repairing OBDII code P2138 can be done by a DIY mechanic, it is recommended to seek professional help for accurate diagnosis and repair.
10. How much does it typically cost to repair OBDII code P2138 in a 2010 Nissan Rogue?
- The cost of repairing OBDII code P2138 can vary depending on the specific cause, but it may range from $200 to $500 for parts and labor.
Discuss the causes and fixes for P2138 2010 Nissan Rogue OBDII Code
Code P2138 2010 Nissan Rogue comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
