AutoCodes – Nissan – P2128 2010 Nissan Rogue

P2128 2010 Nissan Rogue Code - Accelerator Pedal Position Sensor Circuit

Quick Answer

The Accelerator Pedal Position (APP) sensor is installed on the upper end of the accelerator pedal assembly. Common causes include Faulty Accelerator Pedal Position (APP) Sensor, Accelerator Pedal Position (APP) Sensor harness is open or shorted, Accelerator Pedal Position (APP) Sensor circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

What it means: P2128 2010 Nissan Rogue indicates Accelerator Pedal Position Sensor Circuit.
Common causes: Common causes include Faulty Accelerator Pedal Position (APP) Sensor, Accelerator Pedal Position (APP) Sensor harness is open or shorted, Accelerator Pedal Position (APP) Sensor circuit poor electrical connection.
Severity: High - diagnose this code as soon as possible.
Can I drive?: Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

Save to My Repairs My Repairs

AI answers can be wrong. Verify repairs with testing. Open full chat

Code Popularity 2,162

How popular is this code, among other codes? Low

Repair Importance Level

Urgent (Diagnose now) (3 / 3)

Repair Difficulty Level

Intermediate (2 / 3)

What is this?

Table of contents Created and updated by William Orellana on Jun 14, 2020

Description
Possible Causes
How To Fix
Cost to Diagnose
FAQs
Comments
Add Comment

💬 Need more help? Ask Coddy for instant answers — it's free!

Code P2128 2010 Nissan Rogue Description

The Accelerator Pedal Position (APP) sensor is installed on the upper end of the accelerator pedal assembly. The sensor detects the accelerator position and sends a signal to the Engine Control Module (ECM). Accelerator pedal position sensor has two sensors. These sensors are a kind of potentiometers which transform the accelerator pedal position into an output voltage and emit the voltage signal to the ECM. In addition, these sensors detect the opening and closing speed of the accelerator pedal and feed the voltage signals to the ECM. The ECM judges the current opening angle of the accelerator pedal from these signals and controls the throttle control motor based on these signals. Idle position of the accelerator pedal is determined by the ECM receiving the signal from the accelerator pedal position sensor. The ECM uses this signal for the engine operation such as fuel cut.

OBDII Code P2128 2010 Nissan Rogue - Accelerator Pedal Position Sensor Circuit - AutoCodes.com — P2128 2010 Nissan Rogue Code - Accelerator Pedal Position Sensor Circuit

What does this mean?

What are the Possible Causes of the DTC P2128 2010 Nissan Rogue?

Faulty Accelerator Pedal Position (APP) Sensor
Accelerator Pedal Position (APP) Sensor harness is open or shorted
Accelerator Pedal Position (APP) Sensor circuit poor electrical connection
Faulty Engine Control Module (ECM)
Electric Throttle Control Actuator(Throttle Body)

How to Fix the DTC P2128 2010 Nissan Rogue?

Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.

What is the Cost to Diagnose the Code?

Labor: 1.0

To diagnose the P2128 2010 Nissan Rogue code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.

Need more information about the P2128 2010 Nissan Rogue code?

Need more information on how to fix the P2128 2010 Nissan Rogue code? Get Access to Factory Service Manuals

Need Help with the Code?

Get the P2128 2010 Nissan Rogue code diagnosed by a professional: Find a repair shop in your area

About the author: William Orellana is a Master Mechanic and Mechanical Engineer with over 30 years of experience diagnosing and repairing vehicles. Learn more about his background.

Frequently Asked Questions about P2128 2010 Nissan Rogue Code

1. What is OBDII code P2128 in a 2010 Nissan Rogue?

The OBDII code P2128 in a 2010 Nissan Rogue refers to an issue with the Accelerator Pedal Position Sensor Circuit.

2. What are the common symptoms of OBDII code P2128 in a 2010 Nissan Rogue?

Common symptoms of OBDII code P2128 in a 2010 Nissan Rogue include reduced engine power, hesitation or jerking during acceleration, and the vehicle going into limp mode.

3. What are the possible causes of OBDII code P2128 in a 2010 Nissan Rogue?

Possible causes of OBDII code P2128 in a 2010 Nissan Rogue include a faulty accelerator pedal position sensor, damaged wiring or connectors in the sensor circuit, or issues with the engine control module.

4. How can I diagnose OBDII code P2128 in a 2010 Nissan Rogue?

Diagnosing OBDII code P2128 in a 2010 Nissan Rogue involves using a scan tool to retrieve the trouble codes, checking the accelerator pedal position sensor for proper operation, and inspecting the sensor circuit for any faults.

5. How can I repair OBDII code P2128 in a 2010 Nissan Rogue?

Repairing OBDII code P2128 in a 2010 Nissan Rogue may involve replacing the accelerator pedal position sensor, repairing or replacing damaged wiring or connectors, or reprogramming the engine control module.

6. Can I continue driving my 2010 Nissan Rogue with OBDII code P2128?

It is not recommended to continue driving your 2010 Nissan Rogue with OBDII code P2128, as it can lead to further damage to the vehicle and potentially unsafe driving conditions.

7. How much does it cost to fix OBDII code P2128 in a 2010 Nissan Rogue?

The cost to fix OBDII code P2128 in a 2010 Nissan Rogue can vary depending on the exact cause of the issue, but it may range from $100 to $300 for parts and labor.

8. Will resetting the OBDII code P2128 in a 2010 Nissan Rogue make it go away permanently?

Resetting the OBDII code P2128 in a 2010 Nissan Rogue may temporarily clear the code, but if the underlying issue is not addressed, the code is likely to reappear.

9. Can a DIY enthusiast fix OBDII code P2128 in a 2010 Nissan Rogue?

While some aspects of diagnosing and repairing OBDII code P2128 in a 2010 Nissan Rogue can be done by a DIY enthusiast, it is recommended to consult a professional mechanic for a proper diagnosis and repair.

10. How often does OBDII code P2128 occur in a 2010 Nissan Rogue?

OBDII code P2128 in a 2010 Nissan Rogue is not a common issue, but it can occur due to various factors such as sensor wear, wiring issues, or electronic control module malfunctions.