P2122 2010 Nissan Rogue Code - Accelerator Pedal Position Sensor Circuit Range/Performance
Quick Answer
The Accelerator Pedal Position (APP) sensor is installed on the upper end of the accelerator pedal assembly. Common causes include Faulty Accelerator Pedal Position Sensor, Accelerator Pedal Position Sensor harness is open or shorted, Accelerator Pedal Position Sensor circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P2122 2010 Nissan Rogue indicates Accelerator Pedal Position Sensor Circuit Range/Performance.
- Common causes
- Common causes include Faulty Accelerator Pedal Position Sensor, Accelerator Pedal Position Sensor harness is open or shorted, Accelerator Pedal Position Sensor circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P2122 2010 Nissan Rogue Description
Accelerator pedal position sensor has two sensors. These sensors are a kind of potentiometers which transform the accelerator pedal position into output voltage, and emit the voltage signal to the ECM.
In addition, these sensors detect the opening and closing speed of the accelerator pedal and feed the voltage signals to the ECM. The ECM judges the current opening angle of the accelerator pedal from these signals and controls the throttle control motor based on these signals.
Idle position of the accelerator pedal is determined by the ECM receiving the signal from the accelerator pedal position sensor. The ECM uses this signal for the engine operation
such as fuel cut.
What are the Possible Causes of the DTC P2122 2010 Nissan Rogue?
- Faulty Accelerator Pedal Position Sensor
- Accelerator Pedal Position Sensor harness is open or shorted
- Accelerator Pedal Position Sensor circuit poor electrical connection
How to Fix the DTC P2122 2010 Nissan Rogue?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P2122 2010 Nissan Rogue code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P2122 2010 Nissan Rogue code?
Need more information on how to fix the P2122 2010 Nissan Rogue code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P2122 2010 Nissan Rogue code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P2122 2010 Nissan Rogue Code
1. What does the OBDII code P2122 for a 2010 Nissan Rogue indicate?
The OBDII code P2122 in a 2010 Nissan Rogue specifically points to an issue with the Accelerator Pedal Position Sensor Circuit Range/Performance.
2. What are some common symptoms of the P2122 code in a 2010 Nissan Rogue?
Common symptoms associated with the P2122 code in a 2010 Nissan Rogue include decreased engine performance, unresponsive throttle, and potentially even the vehicle going into "limp mode."
3. What are the possible causes of the P2122 code in a 2010 Nissan Rogue?
The P2122 code in a 2010 Nissan Rogue can be triggered by a faulty accelerator pedal position sensor, damaged wiring or connectors in the sensor circuit, or issues with the engine control module.
4. How can I diagnose the P2122 code in my 2010 Nissan Rogue?
To diagnose the P2122 code in a 2010 Nissan Rogue, you can use an OBDII scanner to read the code and then inspect the accelerator pedal position sensor, its wiring, and connectors for any signs of damage or malfunction.
5. Can I continue driving my 2010 Nissan Rogue with the P2122 code present?
It is not recommended to drive your 2010 Nissan Rogue with the P2122 code present, as it can lead to further damage and potential safety hazards due to the unresponsive throttle.
6. How can I repair the P2122 code in my 2010 Nissan Rogue?
Repairing the P2122 code in a 2010 Nissan Rogue may involve replacing the accelerator pedal position sensor, repairing any damaged wiring or connectors, or resetting the engine control module.
7. Is it possible to reset the P2122 code in a 2010 Nissan Rogue without repairs?
While you can clear the P2122 code with an OBDII scanner, it is essential to address the underlying issue causing the code to prevent it from reoccurring.
8. How much does it cost to fix the P2122 code in a 2010 Nissan Rogue?
The cost of fixing the P2122 code in a 2010 Nissan Rogue can vary depending on the extent of the issue, but it may involve parts and labor costs for sensor replacement or wiring repairs.
9. Can a DIY enthusiast fix the P2122 code issue in a 2010 Nissan Rogue?
If you have the necessary tools, knowledge, and experience, you may be able to address the P2122 code issue in a 2010 Nissan Rogue yourself by following repair guides or tutorials.
10. How often does the P2122 code occur in a 2010 Nissan Rogue?
The P2122 code in a 2010 Nissan Rogue can occur sporadically due to sensor or wiring issues, but addressing it promptly is crucial to prevent further complications.
Discuss the causes and fixes for P2122 2010 Nissan Rogue OBDII Code
Code P2122 2010 Nissan Rogue comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
