P2122 2008 Nissan Rogue Code - Accelerator Pedal Position Sensor Circuit Range/Performance
Quick Answer
The Accelerator Pedal Position (APP) sensor is installed on the upper end of the accelerator pedal assembly. Common causes include Faulty Accelerator Pedal Position Sensor, Accelerator Pedal Position Sensor harness is open or shorted, Accelerator Pedal Position Sensor circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P2122 2008 Nissan Rogue indicates Accelerator Pedal Position Sensor Circuit Range/Performance.
- Common causes
- Common causes include Faulty Accelerator Pedal Position Sensor, Accelerator Pedal Position Sensor harness is open or shorted, Accelerator Pedal Position Sensor circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P2122 2008 Nissan Rogue Description
Accelerator pedal position sensor has two sensors. These sensors are a kind of potentiometers which transform the accelerator pedal position into output voltage, and emit the voltage signal to the ECM.
In addition, these sensors detect the opening and closing speed of the accelerator pedal and feed the voltage signals to the ECM. The ECM judges the current opening angle of the accelerator pedal from these signals and controls the throttle control motor based on these signals.
Idle position of the accelerator pedal is determined by the ECM receiving the signal from the accelerator pedal position sensor. The ECM uses this signal for the engine operation
such as fuel cut.
What are the Possible Causes of the DTC P2122 2008 Nissan Rogue?
- Faulty Accelerator Pedal Position Sensor
- Accelerator Pedal Position Sensor harness is open or shorted
- Accelerator Pedal Position Sensor circuit poor electrical connection
How to Fix the DTC P2122 2008 Nissan Rogue?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P2122 2008 Nissan Rogue code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P2122 2008 Nissan Rogue code?
Need more information on how to fix the P2122 2008 Nissan Rogue code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P2122 2008 Nissan Rogue code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P2122 2008 Nissan Rogue Code
1. What are the common symptoms of OBDII code P2122 in a 2008 Nissan Rogue?
- Common symptoms include loss of power, hesitation during acceleration, rough idle, and the vehicle going into limp mode.
2. What does the OBDII code P2122 mean for a 2008 Nissan Rogue?
- OBDII code P2122 on a 2008 Nissan Rogue indicates a problem with the Accelerator Pedal Position Sensor Circuit Range/Performance.
3. What are the possible causes of OBDII code P2122 in a 2008 Nissan Rogue?
- Possible causes include a faulty accelerator pedal position sensor, issues with the sensor's wiring or connectors, or a problem with the engine control module (ECM).
4. How can I diagnose the issue causing OBDII code P2122 on my 2008 Nissan Rogue?
- A thorough diagnostic process involves checking the accelerator pedal position sensor's wiring and connectors, testing the sensor's resistance, and scanning the ECM for any related fault codes.
5. Can I continue driving my 2008 Nissan Rogue with OBDII code P2122?
- It is not recommended to continue driving your vehicle with OBDII code P2122, as it can lead to further damage and safety risks. It's best to address the issue promptly.
6. What are some repair tips for fixing OBDII code P2122 on a 2008 Nissan Rogue?
- Repair tips include inspecting and cleaning the sensor's connectors, replacing the accelerator pedal position sensor if necessary, and ensuring proper wiring connections.
7. How much does it typically cost to repair OBDII code P2122 on a 2008 Nissan Rogue?
- The cost of repairing OBDII code P2122 can vary depending on the exact cause of the issue, but it may range from $100 to $300 for parts and labor.
8. Can a DIY enthusiast fix OBDII code P2122 on a 2008 Nissan Rogue?
- While some enthusiasts may have the skills to diagnose and repair OBDII code P2122, it is recommended to seek professional help to ensure the issue is properly addressed.
9. Will resetting the OBDII code P2122 in my 2008 Nissan Rogue make it go away permanently?
- Resetting the code may temporarily make the warning light disappear, but if the underlying issue is not fixed, the code is likely to reappear once the problem is detected again.
10. How long does it take to repair OBDII code P2122 on a 2008 Nissan Rogue?
- The repair time for OBDII code P2122 can vary depending on the exact cause of the issue and the availability of parts, but it typically takes a few hours to complete the repair.
Discuss the causes and fixes for P2122 2008 Nissan Rogue OBDII Code
Code P2122 2008 Nissan Rogue comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
