P2014 2008 Ford Fusion Code - Intake Manifold Runner Position Sensor/Switch Circuit Bank 1
Quick Answer
The Intake Manifold Runner Control (IMRC) system is monitored for failure during continuous or Key On Engine Off (KOEO) self-test. Common causes include Intake manifold runner control monitor circuit open, Mechanical concern, bind, seize, damage or obstruction of IMRC hardware. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P2014 2008 Ford Fusion indicates Intake Manifold Runner Position Sensor/Switch Circuit Bank 1.
- Common causes
- Common causes include Intake manifold runner control monitor circuit open, Mechanical concern, bind, seize, damage or obstruction of IMRC hardware.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P2014 2008 Ford Fusion Description
What are the Possible Causes of the DTC P2014 2008 Ford Fusion?
- Intake manifold runner control monitor circuit open
- Mechanical concern
- bind, seize, damage or obstruction of IMRC hardware
How to Fix the DTC P2014 2008 Ford Fusion?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P2014 2008 Ford Fusion code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P2014 2008 Ford Fusion code?
Need more information on how to fix the P2014 2008 Ford Fusion code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P2014 2008 Ford Fusion code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P2014 2008 Ford Fusion Code
1. What are the common symptoms of an Intake Manifold Runner Position Sensor/Switch Circuit Bank 1 issue (OBDII code P2014) in a 2008 Ford Fusion?
Common symptoms include rough idling, reduced engine performance, and the Check Engine Light illuminating on the dashboard.
2. What are the possible causes of OBDII code P2014 in a 2008 Ford Fusion?
The code P2014 in a 2008 Ford Fusion is typically caused by a faulty intake manifold runner position sensor/switch or issues with the wiring and connections related to this sensor.
3. How can I diagnose the Intake Manifold Runner Position Sensor/Switch Circuit Bank 1 problem in my 2008 Ford Fusion?
Diagnosing the issue involves using an OBDII scanner to retrieve the trouble code, inspecting the intake manifold runner position sensor/switch and its wiring for damage, and performing tests to determine if the sensor is functioning properly.
4. Can I continue driving my 2008 Ford Fusion with OBDII code P2014?
It is not recommended to drive with a faulty intake manifold runner position sensor/switch, as it can lead to poor engine performance and potential damage over time. It is best to address the issue promptly.
5. How can I repair OBDII code P2014 in my 2008 Ford Fusion?
The repair typically involves replacing the intake manifold runner position sensor/switch and addressing any wiring or connection issues. It is recommended to consult a professional mechanic for proper diagnosis and repair.
6. Are there any DIY tips for fixing the Intake Manifold Runner Position Sensor/Switch Circuit Bank 1 problem in a 2008 Ford Fusion?
While some DIY enthusiasts may attempt to replace the sensor themselves, it is important to have the necessary tools and knowledge to do so correctly. If unsure, it is best to seek professional help.
7. How much does it cost to repair OBDII code P2014 in a 2008 Ford Fusion?
The cost of repairing OBDII code P2014 can vary depending on the extent of the issue, the cost of the replacement sensor, and labor charges. It is advisable to get quotes from different mechanics for an accurate estimate.
8. Will resetting the Check Engine Light resolve OBDII code P2014 in my 2008 Ford Fusion?
Resetting the Check Engine Light may temporarily turn off the warning indicator, but it will not fix the underlying issue causing OBDII code P2014. The problem should be properly diagnosed and repaired to prevent further issues.
9. Can a dirty or clogged intake manifold cause OBDII code P2014 in a 2008 Ford Fusion?
While a dirty or clogged intake manifold may affect engine performance, it is not a direct cause of OBDII code P2014. The code is typically related to the intake manifold runner position sensor/switch circuit.
10. How long does it take to repair OBDII code P2014 in a 2008 Ford Fusion?
The repair time for OBDII code P2014 can vary depending on the mechanic's experience, availability of parts, and the extent of the issue. In general, it may take a few hours to a half-day to complete the repair.
Discuss the causes and fixes for P2014 2008 Ford Fusion OBDII Code
Code P2014 2008 Ford Fusion comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
