P1864 GMC Code - Torque Converter Clutch Enable Solenoid Electrical Fault Conditions
Quick Answer
The Torque Converter Clutch (TCC) Solenoid Valve is an electrical device used with the TCC PWM Solenoid Valve in order to control the fluid acting on the TCC valve. Common causes include Faulty Torque Converter Clutch (TCC), Torque Converter Clutch (TCC) harness is open or shorted, Torque Converter Clutch (TCC) circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P1864 GMC indicates Torque Converter Clutch Enable Solenoid Electrical Fault Conditions.
- Common causes
- Common causes include Faulty Torque Converter Clutch (TCC), Torque Converter Clutch (TCC) harness is open or shorted, Torque Converter Clutch (TCC) circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P1864 GMC Description
With the engine speed over 500 rpm for 5 seconds, not in Fuel Shut-off mode, the Powertrain Control Module (PCM) detects the Torque Converter Clutch (TCC) Solenoid Control voltage did not meet calibration (too high or too low). - Refer to the correct code repair chart in other manuals or media.
What are the Possible Causes of the DTC P1864 GMC?
- Faulty Torque Converter Clutch (TCC)
- Torque Converter Clutch (TCC) harness is open or shorted
- Torque Converter Clutch (TCC) circuit poor electrical connection
How to Fix the DTC P1864 GMC?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P1864 GMC code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P1864 GMC code?
Need more information on how to fix the P1864 GMC code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P1864 GMC code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P1864 GMC Code
1. What are the common symptoms of OBDII code P1864 GMC related to the Torque Converter Clutch Enable Solenoid Electrical Fault Conditions?
- Common symptoms include transmission slipping, harsh shifting, decreased fuel efficiency, and the Check Engine light illuminating.
2. What are the possible causes of OBDII code P1864 GMC indicating Torque Converter Clutch Enable Solenoid Electrical Fault Conditions?
- The possible causes may include a faulty torque converter clutch solenoid, damaged wiring or connectors, low transmission fluid levels, or a malfunctioning PCM.
3. How can I diagnose OBDII code P1864 GMC for Torque Converter Clutch Enable Solenoid Electrical Fault Conditions?
- Diagnosis involves using a scan tool to read the code, checking the transmission fluid level and condition, inspecting the wiring and connectors for damage, and testing the torque converter clutch solenoid.
4. Can I continue driving my vehicle with OBDII code P1864 GMC until I repair it?
- It is not recommended to continue driving with this code as it can lead to further damage to the transmission and decrease in overall vehicle performance.
5. How can I repair OBDII code P1864 GMC for Torque Converter Clutch Enable Solenoid Electrical Fault Conditions?
- The repair may involve replacing the torque converter clutch solenoid, repairing or replacing damaged wiring, ensuring proper transmission fluid levels, and clearing the trouble code.
6. Is it necessary to visit a mechanic for OBDII code P1864 GMC repair?
- While some DIY enthusiasts may be able to address this issue themselves, it is recommended to consult a qualified mechanic for an accurate diagnosis and proper repair.
7. Are there any preventive measures to avoid OBDII code P1864 GMC related to Torque Converter Clutch Enable Solenoid Electrical Fault Conditions?
- Regular maintenance, such as checking transmission fluid levels and condition, can help prevent issues that may trigger this fault code.
8. Can a faulty torque converter clutch solenoid cause other transmission problems besides triggering OBDII code P1864 GMC?
- Yes, a faulty torque converter clutch solenoid can lead to various transmission issues such as erratic shifting, overheating, and reduced fuel efficiency.
9. How long does it typically take to repair OBDII code P1864 GMC for Torque Converter Clutch Enable Solenoid Electrical Fault Conditions?
- The repair time can vary depending on the exact cause of the issue and the availability of parts, but it may take anywhere from a few hours to a full day to complete the repair.
10. Will resetting the Check Engine light after repairing OBDII code P1864 GMC make it disappear permanently?
- After repairing the issue triggering the fault code, resetting the Check Engine light should make it disappear permanently if the problem has been successfully resolved.
Discuss the causes and fixes for P1864 GMC OBDII Code
Code P1864 GMC comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
