P1762 Dodge Code - Governor Pressure Sensor Offset Voltage Too High or Low
Quick Answer
With the engine running, the Diagnostic Trouble Code (DTC) will be set when the Powertrain Control Module (PCM) detects that the Governor Pressure sensor signal was over or under the specified value stored in memory for 1.32 seconds. Common causes include Internal transmission failure, Faulty Governor Pressure Sensor, Governor Pressure Sensor harness open or shorted. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P1762 Dodge indicates Governor Pressure Sensor Offset Voltage Too High or Low.
- Common causes
- Common causes include Internal transmission failure, Faulty Governor Pressure Sensor, Governor Pressure Sensor harness open or shorted.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P1762 Dodge Description
What are the Possible Causes of the DTC P1762 Dodge?
- Internal transmission failure
- Faulty Governor Pressure Sensor
- Governor Pressure Sensor harness open or shorted
- Governor Pressure Sensor circuit poor electrical connection
How to Fix the DTC P1762 Dodge?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P1762 Dodge code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P1762 Dodge code?
Need more information on how to fix the P1762 Dodge code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P1762 Dodge code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P1762 Dodge Code
1. What does the OBDII code P1762 mean on a Dodge?
The P1762 code in a Dodge vehicle indicates that the governor pressure sensor offset voltage is either too high or too low, suggesting a potential issue with the transmission's pressure regulation.
2. What are the common symptoms of code P1762 in a Dodge?
Symptoms of the P1762 code may include erratic shifting, transmission slipping, the transmission going into 'limp' mode, decreased fuel efficiency, and a check engine light.
3. What causes the P1762 code to appear on a Dodge?
Possible causes for the P1762 code include a faulty governor pressure sensor, issues with the governor pressure solenoid, wiring problems (shorts or opens), or a malfunctioning transmission control module (TCM).
4. How can I fix the P1762 code on my Dodge?
To fix the P1762 code, start by checking and, if necessary, replacing the governor pressure sensor and solenoid. Also, inspect the wiring and connectors for damage and ensure the transmission control module is functioning properly.
5. Is it safe to drive my Dodge with the P1762 code?
Driving with the P1762 code can lead to further transmission damage. It's advisable to address the issue as soon as possible to avoid more severe problems like complete transmission failure.
6. How do I diagnose the P1762 code in a Dodge?
Diagnosing the P1762 code involves scanning the vehicle with an OBDII scanner, visually inspecting the governor pressure sensor and solenoid, and checking for any damaged wiring or connectors. A transmission fluid check may also be necessary to rule out low fluid or contamination as a contributing factor.
7. Can a faulty governor pressure sensor trigger the P1762 code in a Dodge?
Yes, a faulty governor pressure sensor is one of the primary triggers for the P1762 code. This sensor helps regulate the hydraulic pressure based on the vehicle's speed and load, and its failure can disrupt normal transmission functions.
8. What maintenance should be performed after repairing the P1762 issue in a Dodge?
After repairing the P1762 issue, it's recommended to clear the code with an OBDII scanner, perform a test drive to ensure the transmission is functioning correctly, and possibly change the transmission fluid if it hasn't been replaced recently.
9. How much does it typically cost to resolve the P1762 code in a Dodge?
The cost to resolve the P1762 code can vary widely depending on the cause. Replacing a governor pressure sensor or solenoid can cost between $150 and $400 including parts and labor, while more extensive repairs like wiring fixes or transmission control module replacement can increase the expense significantly.
10. What tools are needed to diagnose and repair the P1762 code on a Dodge?
Repairing the P1762 code typically requires an OBDII scan tool, a multimeter for electrical testing, basic hand tools for removing components, and potentially a pressure gauge for testing transmission fluid pressure.
Discuss the causes and fixes for P1762 Dodge OBDII Code
-
1999 dodge durango slt. It has the 44re transmission. I did a filter and fluid change on it and it seemed to be alright for about a month. But now the check engine light is back on and its showing the code 1762 on my code reader.
-
I check a national database of repair for your model and year, and the most common cause for the P1762 is the Automatic Transmission Governor Pressure Solenoid, followed by the Automatic Transmission Governor Pressure Sensor.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
