P16E4 Buick Code - Sensor Communication Circuit 3 Low Voltage
Quick Answer
The Engine Control Module (ECM) uses the Fuel Rail Pressure (FRP) sensor to constantly adjust the high-pressure fuel pump's feed rate so that the ideal pressure is permanently maintained in the high-pressure section (between the high-pressure fuel pump and the injectors) by means of closed-loop control. Common causes include Low or no fuel, Faulty Fuel Rail Pressure (FRP) Sensor, Fuel Rail Pressure harness is open or shorted. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P16E4 Buick indicates Sensor Communication Circuit 3 Low Voltage.
- Common causes
- Common causes include Low or no fuel, Faulty Fuel Rail Pressure (FRP) Sensor, Fuel Rail Pressure harness is open or shorted.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P16E4 Buick Description
What are the Possible Causes of the DTC P16E4 Buick?
- Low or no fuel
- Faulty Fuel Rail Pressure (FRP) Sensor
- Fuel Rail Pressure harness is open or shorted
- Fuel Rail Pressure circuit poor electrical connection
- Faulty Fuel Pump
How to Fix the DTC P16E4 Buick?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P16E4 Buick code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P16E4 Buick code?
Need more information on how to fix the P16E4 Buick code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P16E4 Buick code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P16E4 Buick Code
1. What are common symptoms of OBDII code P16E4 in a Buick related to Sensor Communication Circuit 3 Low Voltage?
Common symptoms include rough idling, poor engine performance, decreased fuel efficiency, and illuminated Check Engine Light.
2. What are some possible causes for the P16E4 code in a Buick?
Potential causes may include a faulty sensor, damaged wiring or connectors, a malfunctioning control module, or a low vehicle battery voltage.
3. How can I diagnose the cause of the Sensor Communication Circuit 3 Low Voltage issue in my Buick?
To diagnose the problem, you can use an OBDII scanner to retrieve the fault code and then inspect the sensor, wiring, connectors, and control module for any visible signs of damage or corrosion.
4. Can I continue driving my Buick with the P16E4 trouble code present?
It is not recommended to drive your vehicle with the P16E4 code active, as it can lead to further damage to the engine or emissions system. It's best to address the issue promptly.
5. What is the typical repair process for OBDII code P16E4 in a Buick?
The repair process usually involves identifying and fixing the underlying cause of the low voltage issue, which may include replacing a faulty sensor, repairing damaged wiring, or resetting the control module.
6. Is it possible to reset the P16E4 trouble code in a Buick without addressing the root cause?
While you can clear the code using an OBDII scanner, the Check Engine Light is likely to reappear if the underlying issue is not resolved. It's important to fix the root cause to prevent further problems.
7. How much does it cost to repair the Sensor Communication Circuit 3 Low Voltage problem in a Buick?
The cost of repairs can vary depending on the specific issue causing the code, the labor rates in your area, and whether you choose to address the problem yourself or take your vehicle to a mechanic.
8. Are there any preventative maintenance tips to avoid encountering the P16E4 code in a Buick?
Regularly checking and maintaining your vehicle's sensors, wiring, and connectors can help prevent issues like low voltage in the Sensor Communication Circuit 3, reducing the likelihood of encountering this trouble code.
9. Can extreme weather conditions affect the occurrence of the P16E4 code in a Buick?
Yes, extreme temperatures or weather conditions can sometimes impact the performance of sensors and electrical components, potentially leading to issues like low voltage in the communication circuit and triggering the P16E4 code.
10. How long does it typically take to repair the P16E4 code issue in a Buick?
The repair time can vary depending on the complexity of the problem and the availability of parts. In some cases, fixing the Sensor Communication Circuit 3 Low Voltage issue can be done within a few hours, while more complex issues may take longer to diagnose and repair.
Discuss the causes and fixes for P16E4 Buick OBDII Code
Code P16E4 Buick comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
