P11EE MINI Code - Throttle/Pedal Positio Sensor/Switch 'E' Circuit Voltage Low
Quick Answer
The accelerator pedal position is monitored separately by 2 individual sensors. Common causes include Faulty Accelerator Pedal, Accelerator Pedal harness is open or shorted, Accelerator Pedal circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P11EE MINI indicates Throttle/Pedal Positio Sensor/Switch 'E' Circuit Voltage Low.
- Common causes
- Common causes include Faulty Accelerator Pedal, Accelerator Pedal harness is open or shorted, Accelerator Pedal circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P11EE MINI Description
Each change in the accelerator-pedal position is transmitted to the engine-management control unit with a maximum lag of 50 milliseconds. Sensor signals are transmitted in analog form. The engine-management control unit monitors the two input signals from the sensors and compares them for plausibility (factors such as mutual synchronicity, linearity, etc.).
The Digital Motor Electronics (DME) diagnosis the voltage at the Accelerator Pedal Module Pedal Sensor 2. The Diagnostic Trouble Code (DTC) is detected whenever the voltage at pedal sensor 2 becomes less than a lower limit value times 0.5. Lower limit value: 0.39 V.
What are the Possible Causes of the DTC P11EE MINI?
- Faulty Accelerator Pedal
- Accelerator Pedal harness is open or shorted
- Accelerator Pedal circuit poor electrical connection
- Faulty Accelerator Pedal Module
How to Fix the DTC P11EE MINI?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P11EE MINI code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P11EE MINI code?
Need more information on how to fix the P11EE MINI code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P11EE MINI code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P11EE MINI Code
1. What are the common symptoms of OBDII code P11EE in a MINI related to the Throttle/Pedal Position Sensor/Switch 'E' Circuit Voltage Low?
- Common symptoms include reduced engine performance, rough idling, stalling, and in some cases, the vehicle may go into limp mode.
2. What are the potential causes of OBDII code P11EE in a MINI indicating Throttle/Pedal Position Sensor/Switch 'E' Circuit Voltage Low?
- The code may be triggered by a faulty throttle position sensor, damaged wiring or connectors in the sensor circuit, or a problem with the electronic control module.
3. How can I diagnose the Throttle/Pedal Position Sensor/Switch 'E' Circuit Voltage Low issue in my MINI?
- A thorough inspection of the throttle position sensor and its wiring, as well as using a diagnostic scanner to read and interpret the fault code, can help diagnose the issue.
4. Can I drive my MINI with the OBDII code P11EE present?
- It is not recommended to drive with this code present, as it can lead to decreased engine performance and potential safety hazards. It is best to address the issue promptly.
5. What are some repair tips for fixing OBDII code P11EE in a MINI?
- Repair tips include checking and cleaning the throttle position sensor, inspecting and repairing any damaged wiring or connectors, and resetting the fault code after addressing the root cause.
6. Is it possible to reset the OBDII code P11EE in a MINI without fixing the underlying issue?
- While you can clear the fault code temporarily, it is not advisable as the issue causing the code will persist, potentially leading to further problems down the line.
7. Can a DIY enthusiast fix the Throttle/Pedal Position Sensor/Switch 'E' Circuit Voltage Low issue in a MINI?
- Depending on the DIY skills and tools available, some enthusiasts may be able to address this issue by following repair guides or seeking assistance from online forums.
8. Will replacing the throttle position sensor solve the OBDII code P11EE in a MINI?
- In many cases, replacing a faulty throttle position sensor can resolve the issue. However, it is essential to diagnose the problem correctly to ensure the right component is replaced.
9. How much does it typically cost to repair the Throttle/Pedal Position Sensor/Switch 'E' Circuit Voltage Low issue in a MINI?
- The cost of repair can vary based on the root cause of the problem, the labor rates in your area, and whether you choose to address the issue yourself or take it to a professional mechanic.
10. What steps should I take if the OBDII code P11EE persists after attempted repairs in my MINI?
- If the code persists after attempted repairs, it is advisable to seek the expertise of a qualified mechanic or MINI specialist to conduct a more in-depth diagnosis and repair of the issue.
Discuss the causes and fixes for P11EE MINI OBDII Code
Code P11EE MINI comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
