AutoCodes – Ford – P1151 2000 Ford F150

P1151 2000 Ford F150 Code - Lack of Upstream Heated Oxygen Sensor Switch Sensor Indicates Lean Bank 2

Quick Answer

The Heated Oxygen Sensor (HO2S) Monitor is an on-board strategy designed to monitor the HO2S sensors for a malfunction or deterioration that can affect emissions. Common causes include Faulty Upstream Oxygen Sensor Bank 2, Fuel pressure high or low, MAF sensor dirty/defective. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

What it means: P1151 2000 Ford F150 indicates Lack of Upstream Heated Oxygen Sensor Switch Sensor Indicates Lean Bank 2.
Common causes: Common causes include Faulty Upstream Oxygen Sensor Bank 2, Fuel pressure high or low, MAF sensor dirty/defective.
Severity: High - diagnose this code as soon as possible.
Can I drive?: Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

Save to My Repairs My Repairs

AI answers can be wrong. Verify repairs with testing. Open full chat

Code Popularity 9,194

How popular is this code, among other codes? Low

Repair Importance Level

Urgent (Diagnose now) (3 / 3)

Repair Difficulty Level

Intermediate (2 / 3)

What is this?

Table of contents Created and updated by William Orellana on May 03, 2019

Description
Possible Causes
How To Fix
Tech Notes
Cost to Diagnose
FAQs
Comments
Add Comment

💬 Need more help? Ask Coddy for instant answers — it's free!

Code P1151 2000 Ford F150 Description

The Heated Oxygen Sensor (HO2S) Monitor is an on-board strategy designed to monitor the HO2S sensors for a malfunction or deterioration that can affect emissions. Under specific conditions, the fuel control or upstream HO2S sensors are checked for proper output voltage and response rate (the time it takes to switch from lean to rich or rich to lean). Downstream HO2S sensors used for Catalyst Monitor are also monitored for proper output voltage. Input is required from the Engine Coolant Temperature (ECT) or Cylinder Head Temperature (CHT), Inlet Air Temperature (IAT), Mass Air Flow (MAF), Throttle Position (TP) and Crankshaft Position (CKP) sensors to activate the HO2S Monitor. The Fuel System Monitor and Misfire Detection Monitor must also have completed successfully before the HO2S Monitor is enabled.
• The HO2S sensor senses the oxygen content in the exhaust flow and outputs a voltage between zero and 1.0 volt. Lean of stoichiometric (air/fuel ratio of approximately 14.7:1 for gasoline engines), the HO2S will generate a voltage between zero and 0.45 volt. Rich of stoichiometric, the HO2S will generate a voltage between 0.45 and 1.0 volt.
• The HO2S Monitor evaluates both the upstream (Fuel Control) and downstream (Catalyst Monitor) HO2S for proper function.
• Once the HO2S Monitor is enabled, the upstream HO2S signal voltage amplitude and response frequency are checked. Excessive voltage is determined by comparing the HO2S signal voltage to a maximum calibratable threshold voltage.
• A fixed frequency closed loop fuel control routine is executed and the upstream HO2S voltage amplitude and output response frequency are observed. A sample of the upstream HO2S signal is evaluated to determine if the sensor is capable of switching or has a slow response rate.
• An HO2S heater circuit fault is determined by turning the heater on and off and looking for a corresponding change in the OSM and by
measuring the current going through the heater circuit.
• The MIL is activated after a fault is detected on two consecutive OBD II drive cycles.

OBDII Code P1151 2000 Ford F150 - Lack of Upstream Heated Oxygen Sensor Switch Sensor Indicates Lean Bank 2 - AutoCodes.com — P1151 2000 Ford F150 Code - Lack of Upstream Heated Oxygen Sensor Switch Sensor Indicates Lean Bank 2

What does this mean?

What are the Possible Causes of the DTC P1151 2000 Ford F150?

Faulty Upstream Oxygen Sensor Bank 2
Fuel pressure high or low
MAF sensor dirty/defective
Vacuum leak on engine
Leaking fuel injector or fuel pressure regulator
Faulty Powertrain Control Module (PCM)

How to Fix the DTC P1151 2000 Ford F150?

Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.

What does this mean?

Code Tech Notes

The code means that the Powertrain Control Module (PCM) has detected a lean system, which means that there is either not enough fuel or and excessive amount of air in the system. Start by checking for vacuum leaks.

What is the Cost to Diagnose the Code?

Labor: 1.0

To diagnose the P1151 2000 Ford F150 code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.

Need more information about the P1151 2000 Ford F150 code?

Need more information on how to fix the P1151 2000 Ford F150 code? Get Access to Factory Service Manuals

Need Help with the Code?

Get the P1151 2000 Ford F150 code diagnosed by a professional: Find a repair shop in your area

About the author: William Orellana is a Master Mechanic and Mechanical Engineer with over 30 years of experience diagnosing and repairing vehicles. Learn more about his background.

Frequently Asked Questions about P1151 2000 Ford F150 Code

1. What are the common symptoms of OBDII code P1151 on a 2000 Ford F150?

- Common symptoms include poor fuel economy, rough idle, engine misfires, and potential stalling.

2. What does the OBDII code P1151 "Lack of Upstream Heated Oxygen Sensor Switch Sensor Indicates Lean Bank 2" mean?

- This code indicates that the upstream oxygen sensor in bank 2 is detecting a lean air-fuel mixture, which can lead to poor engine performance.

3. What are the possible causes of OBDII code P1151 on a 2000 Ford F150?

- Common causes include a faulty oxygen sensor, vacuum leaks, fuel system issues, exhaust leaks, or a problem with the Mass Air Flow (MAF) sensor.

4. How can I diagnose the cause of OBDII code P1151 on my 2000 Ford F150?

- Diagnose by performing a visual inspection for leaks, testing the oxygen sensor, checking the fuel pressure, examining the MAF sensor, and scanning for any other related codes.

5. Can I continue driving my 2000 Ford F150 with OBDII code P1151?

- It is not recommended to drive with this code as it can lead to further damage to the engine and catalytic converter over time.

6. How can I repair OBDII code P1151 on a 2000 Ford F150?

- Repair options include replacing the upstream oxygen sensor, fixing any vacuum or exhaust leaks, cleaning or replacing the MAF sensor, and addressing any fuel system issues.

7. Is it possible for a DIY enthusiast to fix OBDII code P1151 on a 2000 Ford F150?

- Yes, some repairs related to this code can be done by a DIY enthusiast with the right tools and knowledge, such as replacing the oxygen sensor or fixing minor vacuum leaks.

8. How much does it typically cost to repair OBDII code P1151 on a 2000 Ford F150?

- The cost of repair can vary depending on the exact cause of the code, but it may range from $100 to $500 or more, including parts and labor.

9. Will resetting the OBDII code P1151 on a 2000 Ford F150 make it go away permanently?

- Resetting the code will clear it temporarily, but if the underlying issue is not fixed, the code is likely to reappear after some driving cycles.

10. How often should I check for OBDII code P1151 on my 2000 Ford F150?

- It's a good practice to regularly monitor your vehicle's performance and check for any stored codes, including P1151, especially if you notice any symptoms of engine trouble.