P112C MINI Code - Upstream Oxygen Sensor Open Circuit Monitoring Virtual Ground Failure or Pumping Current Failure Bank 1
Quick Answer
The oxygen sensor circuit monitoring detects the following malfunctions by evaluating the error information received from oxygen sensor monitoring functions. Common causes include Faulty Upstream Oxygen Sensor Bank 1, Upstream Oxygen Sensor Bank 1 harness is open or shorted, Upstream Oxygen Sensor Bank 1 circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P112C MINI indicates Upstream Oxygen Sensor Open Circuit Monitoring Virtual Ground Failure or Pumping Current Failure Bank 1.
- Common causes
- Common causes include Faulty Upstream Oxygen Sensor Bank 1, Upstream Oxygen Sensor Bank 1 harness is open or shorted, Upstream Oxygen Sensor Bank 1 circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P112C MINI Description
This function shall be triggered only if one of the following diagnosis is active (to set the readiness bit), which are 'Upstream Oxygen Sensor - Signal Monitoring During Fuel Cut-off' and 'Upstream Oxygen Sensor - Heater Monitoring'. The function shall go to the state = “active” only if one of the above diagnosis detected a fault.
An open circuit in line Virtual Ground or in the line Pumping current can be detected if the sensor signal stocks near lambda 1. The sensor non-activity can be detected by the Oxygen Sensor Signal Monitoring During Fuel Cut-off (signal voltage below e.g. 2,1 V *) in fuel cut off).
What are the Possible Causes of the DTC P112C MINI?
- Faulty Upstream Oxygen Sensor Bank 1
- Upstream Oxygen Sensor Bank 1 harness is open or shorted
- Upstream Oxygen Sensor Bank 1 circuit poor electrical connection
How to Fix the DTC P112C MINI?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P112C MINI code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P112C MINI code?
Need more information on how to fix the P112C MINI code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P112C MINI code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P112C MINI Code
1. What are the common symptoms of OBDII code P112C in a MINI related to upstream oxygen sensor issues?
- Common symptoms include poor fuel economy, rough idling, engine misfires, and the illumination of the Check Engine Light.
2. What are the possible causes of the P112C code in a MINI, specifically related to upstream oxygen sensor open circuit monitoring virtual ground failure?
- Possible causes include a faulty oxygen sensor, damaged wiring or connectors, a blown fuse, or issues with the engine control module (ECM).
3. How can I diagnose and repair the upstream oxygen sensor open circuit issue causing the P112C code in my MINI?
- To diagnose, check the wiring and connectors for damage, test the oxygen sensor for proper function, and inspect the ECM. Repair may involve replacing the oxygen sensor, repairing wiring, or addressing ECM issues.
4. What is the significance of virtual ground failure in the context of OBDII code P112C in a MINI?
- Virtual ground failure can disrupt the proper functioning of the upstream oxygen sensor, leading to inaccurate readings and potential engine performance issues.
5. What does "pumping current failure" refer to in relation to the P112C code in a MINI?
- Pumping current failure indicates a malfunction in the circuitry that controls the pumping current of the oxygen sensor, affecting its ability to generate accurate voltage signals.
6. Can driving with the P112C code in a MINI lead to further damage or performance issues?
- Continuing to drive with the P112C code may result in reduced fuel efficiency, increased emissions, and potential damage to the catalytic converter over time.
7. How can I prevent the recurrence of the P112C code related to upstream oxygen sensor issues in my MINI?
- Regular maintenance, such as replacing oxygen sensors at recommended intervals, checking wiring for damage, and addressing any ECM issues promptly, can help prevent the recurrence of the P112C code.
8. Is it safe to drive my MINI with the Check Engine Light on due to the P112C code?
- It is generally safe to drive in the short term, but it is advisable to have the issue diagnosed and repaired as soon as possible to prevent further complications and ensure optimal engine performance.
9. Can a DIY enthusiast with basic automotive knowledge repair the upstream oxygen sensor open circuit issue causing the P112C code in a MINI?
- Depending on the extent of the issue, a DIY enthusiast may be able to address simple causes like damaged wiring or connectors. However, more complex issues may require professional diagnosis and repair.
10. How long does it typically take to repair the upstream oxygen sensor open circuit issue causing the P112C code in a MINI?
- The repair time can vary depending on the exact cause of the issue and the extent of the repairs needed. Simple fixes like replacing a fuse or connector may take less than an hour, while more involved repairs could take several hours or longer.
Discuss the causes and fixes for P112C MINI OBDII Code
Code P112C MINI comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
