AutoCodes - OBDII Code List - P1123 LAND-ROVER

P1123 LAND-ROVER - Accelerator Pedal Position Sensor Short Circuit To Battery

Repair Importance Level: 3/3
Repair Difficulty Level: 2/3    What is this?
Table of contents

P1123 LAND-ROVER Possible Causes

  • Faulty Accelerator Pedal Position (APP) Sensor
  • APP Sensor harness is open or shorted
  • APP Sensor circuit poor electrical connection

How do I fix code P1123 LAND-ROVER?

Check the "Possible Causes" listed above. Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector's pins.
How much do you know about cars?

Take the automotive tests and turbo-charge your car repair knowledge

Play Now

Cost of diagnosing the P1123 LAND-ROVER code

Labor: 1.0

The cost of diagnosing the P1123 LAND-ROVER code is 1.0 hour of labor. The auto repair labor rates vary by location, your vehicle's make and model, and even your engine type. Most auto repairs shops charge between $75 and $150 per hour.

Possible Symptoms

  • Engine Light ON (or Service Engine Soon Warning Light)
  • No throttle response

P1123 LAND-ROVER Description

The Accelerator Pedal Position (APP) sensor is located in plastic housing which is integral with the throttle pedal. The housing is injection moulded and provides location for the APP sensor. The sensor is mounted externally on the housing and is secured with two Torx screws. The external body of the sensor has a six pin connector which accepts a connector on the vehicle wiring harness.
The sensor has a spigot which protrudes into the housing and provides the pivot point for the pedal mechanism. The spigot has a slot which allows for a pin, which is attached to the sensor potentiometers, to rotate through approximately 90°, which relates to pedal movement. The pedal is connected via a link to a drum, which engages with the sensor pin, changing the linear movement of the pedal into rotary movement of the drum. The drum has two steel cables attached to it. The cables are secured to two tension springs which are secured in the opposite end of the housing. The springs provide 'feel' on the pedal movement and require an effort from the driver similar to that of a cable controlled throttle. A detente mechanism is located at the forward end of the housing and is operated by a ball located on the drum. At near maximum throttle pedal movement, the ball contacts the detente mechanism. A spring in the mechanism is compressed and gives the driver the feeling of depressing a 'kickdown' switch when full pedal travel is achieved.
The APP sensor has two potentiometer tracks which each receive a 5V input voltage from the ECM. Track 1 provides an output of 0.5V with the pedal at rest and 2.0V at 100% full throttle. Track 2 provides an output of 0.5V with the pedal at rest and 4.5V at 100% full throttle. The signals from the two tracks are used by the ECM to determine fuelling for engine operation and also by the ECM and the EAT ECU to initiate a kickdown request for the automatic transmission.
The ECM monitors the outputs from each of the potentiometer tracks and can determine the position, rate of change and direction of movement of the throttle pedal. The 'closed throttle' position signal is used by the ECM to initiate idle speed control and also overrun fuel cut-off.
OBDII Code P1123 Land-rover - Accelerator Pedal Position Sensor Short Circuit To Battery -

More Information

Need more information on how to fix the P1123 LAND-ROVER code?
Get Access to Factory Service Manuals

Need more help?

Get the P1123 Land-rover code diagnosed by a professional: Find a repair shop in your area


Help us improve Leave a comment below or tell us if the information above help you fix the code. What are the symptoms on your vehicle for the P1123 Land-rover code? Have you replaced any parts?
Any information is appreciated. Thanks
Top ⇧