P0734 Audi Code - Gear 4 Incorrect Ratio
Quick Answer
This diagnosis monitors actual gear position by checking the torque converter slip ratio calculated by Transmission Control Module (TCM) as follows: Torque converter slip ratio = A x C/B A: Output shaft revolution signal from revolution sensor B: Engine speed signal from Engine Control Module (ECM) C: Gear ratio determined as gear position which TCM supposes If the actual gear position is higher than the position (4th) supposed by TCM, the slip ratio will be more than normal. Common causes include Low transmission fluid level, Dirty transmission fluid, Shift solenoids. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P0734 Audi indicates Gear 4 Incorrect Ratio.
- Common causes
- Common causes include Low transmission fluid level, Dirty transmission fluid, Shift solenoids.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P0734 Audi Description
Torque converter slip ratio = A x C/B
A: Output shaft revolution signal from revolution sensor
B: Engine speed signal from Engine Control Module (ECM)
C: Gear ratio determined as gear position which TCM supposes
If the actual gear position is higher than the position (4th) supposed by TCM, the slip ratio will be more than normal. In case the ratio exceeds the specified value, TCM judges this diagnosis malfunction.
What are the Possible Causes of the DTC P0734 Audi?
- Low transmission fluid level
- Dirty transmission fluid
- Shift solenoids
- Transmission mechanical problems
- Transmission hydraulic control circuit
How to Fix the DTC P0734 Audi?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
Code Tech Notes
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P0734 Audi code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P0734 Audi code?
Need more information on how to fix the P0734 Audi code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P0734 Audi code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P0734 Audi Code
1. What does OBDII code P0734 mean on an Audi?
P0734 indicates "Gear 4 Incorrect Ratio," meaning the transmission is not operating properly in fourth gear, often due to mechanical or electrical issues.
2. What are the common symptoms of code P0734 in an Audi?
Symptoms include transmission slipping, rough shifting, loss of acceleration, poor fuel efficiency, and the check engine light turning on.
3. What causes code P0734 on an Audi?
Common causes include low transmission fluid, worn clutches, faulty shift solenoids, damaged transmission gears, or issues with the transmission control module (TCM).
4. Can low transmission fluid trigger code P0734 on an Audi?
Yes, insufficient or contaminated transmission fluid can cause improper gear ratios and trigger the P0734 code.
5. How do I diagnose code P0734 on my Audi?
Start by checking the transmission fluid level and condition, inspecting the wiring and connectors for damage, and scanning the TCM for additional related codes.
6. Is it safe to drive my Audi with the P0734 code?
Driving with code P0734 can worsen transmission damage and lead to unsafe driving conditions; it's best to address the issue promptly.
7. How can code P0734 be fixed on an Audi?
Repairs may include refilling or replacing the transmission fluid, repairing or replacing faulty solenoids, rebuilding the transmission, or reprogramming the TCM.
8. How much does it cost to repair code P0734 on an Audi?
Repair costs vary widely, from under $100 for fluid replacement to several thousand dollars for a transmission rebuild or replacement.
9. Can a faulty transmission control module cause code P0734 on an Audi?
Yes, a malfunctioning TCM can lead to incorrect gear ratios and trigger the P0734 code.
10. Will clearing the P0734 code fix the problem on an Audi?
Clearing the code without addressing the underlying issue will not fix the problem; the code is likely to return if the cause is not resolved.
Discuss the causes and fixes for P0734 Audi OBDII Code
-
What year is your Audi? how is the transmission fluid level and condition?
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
