P0717 2013 Toyota RAV4 Code - Input Speed Sensor Circuit No Signal
Quick Answer
The Input Speed sensor detects the rotation speed of the turbine which indicates the input speed of the transaxle. Common causes include Faulty Transmission Speed Sensor NT (Transmission Revolution Sensor), Transmission Speed Sensor harness is open or shorted, Transmission Speed Sensor circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P0717 2013 Toyota RAV4 indicates Input Speed Sensor Circuit No Signal.
- Common causes
- Common causes include Faulty Transmission Speed Sensor NT (Transmission Revolution Sensor), Transmission Speed Sensor harness is open or shorted, Transmission Speed Sensor circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P0717 2013 Toyota RAV4 Description
The NT terminal of the ECM detects a pulse signal from the speed sensor NT (input RPM). The ECM calculates gear shifts by comparing the signal from speed sensor NT with the signal from speed sensor NC.
While the transaxle is operating in 2nd, 3rd, 4th, 5th, or 6th gear with the shift lever in D, if the input shaft speed is less than 300 rpm although the output shaft speed is more than 1000 rpm, the ECM interprets this as a fault, illuminates the MIL and stores the Diagnostic Trouble Code (DTC).
What are the Possible Causes of the DTC P0717 2013 Toyota RAV4?
- Faulty Transmission Speed Sensor NT (Transmission Revolution Sensor)
- Transmission Speed Sensor harness is open or shorted
- Transmission Speed Sensor circuit poor electrical connection
- Faulty Engine Control Module (ECM)
How to Fix the DTC P0717 2013 Toyota RAV4?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P0717 2013 Toyota RAV4 code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P0717 2013 Toyota RAV4 code?
Need more information on how to fix the P0717 2013 Toyota RAV4 code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P0717 2013 Toyota RAV4 code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P0717 2013 Toyota RAV4 Code
1. What are the common symptoms of OBDII code P0717 in a 2013 Toyota RAV4?
- Common symptoms include issues with shifting gears, erratic speedometer readings, and the transmission going into limp mode.
2. What does the OBDII code P0717 mean for a 2013 Toyota RAV4?
- The code indicates a problem with the Input Speed Sensor Circuit, specifically that there is no signal being received from the sensor.
3. What are the possible causes of the Input Speed Sensor Circuit No Signal code in a 2013 Toyota RAV4?
- Potential causes include a faulty input speed sensor, damaged wiring or connectors, a malfunctioning transmission control module (TCM), or low transmission fluid levels.
4. How can I diagnose the Input Speed Sensor Circuit No Signal issue in my 2013 Toyota RAV4?
- You can diagnose the problem by checking the wiring and connectors for damage, testing the input speed sensor for proper function, and using a scan tool to read the code and monitor sensor data.
5. Can I continue driving my 2013 Toyota RAV4 with the P0717 code?
- It is not recommended to continue driving with the P0717 code as it can lead to further transmission issues and potential damage if left unresolved.
6. How can I repair the Input Speed Sensor Circuit No Signal problem in my 2013 Toyota RAV4?
- Repair typically involves replacing the faulty input speed sensor, repairing any damaged wiring or connectors, and resetting the trouble code with a scan tool.
7. Is it possible to reset the OBDII code P0717 in a 2013 Toyota RAV4 without fixing the underlying issue?
- While you can clear the code with a scan tool, it is not advisable as the problem will likely reoccur if the root cause is not addressed.
8. How much does it cost to fix the Input Speed Sensor Circuit No Signal issue in a 2013 Toyota RAV4?
- The cost of repair can vary depending on the cause of the issue, but it typically ranges from $200 to $500 including parts and labor.
9. Will replacing the input speed sensor fix the P0717 code in my 2013 Toyota RAV4?
- In many cases, replacing the input speed sensor resolves the P0717 code, but it's important to diagnose the issue properly to ensure a correct repair.
10. Can a DIY enthusiast fix the Input Speed Sensor Circuit No Signal problem in a 2013 Toyota RAV4?
- While some may attempt the repair themselves, it is recommended to have a professional diagnose and repair electrical and transmission-related issues to avoid further complications.
Discuss the causes and fixes for P0717 2013 Toyota RAV4 OBDII Code
Code P0717 2013 Toyota RAV4 comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
