P06CB 2016 GMC Sierra Code - Cylinder 7 Glow Plug Incorrect
Quick Answer
n the diesel engine, air alone is compressed in the cylinder. Common causes include Faulty cylinder #1 glow plug, Cylinder #1 glow plug harness is open or shorted, Cylinder #1 glow plug circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P06CB 2016 GMC Sierra indicates Cylinder 7 Glow Plug Incorrect.
- Common causes
- Common causes include Faulty cylinder #1 glow plug, Cylinder #1 glow plug harness is open or shorted, Cylinder #1 glow plug circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P06CB 2016 GMC Sierra Description
Control of the glow plugs is accomplished by the glow plug control module. The nominal voltage for the glow plugs is 5.4 volts. When the ignition is turned On, the glow plug control module applies 7.2 V for 2.2 s, then 5.7 V for 0.8 s, and then 5.4 V until 1200°C (2192°F) is reached. The maximum voltage of the system is 10 V. While the engine is running the voltage will vary between 4.7 - 10 V when in closed loop control to maintain a glow plug temperature that ranges from 1150° - 1180°C (2102° - 2156°F). The temperature and the power consumption are controlled between the Engine Control Module (ECM) and the glow plug control module within a wide range to suit the engine's pre-heating requirements. Each glow plug is energized individually. This capability yields more optimum heat times for the glow plugs, thus pre - glow times can be kept to a minimum for a short wait to crank times and maximum glow plug durability. A Diagnostic Trouble Code (DTC) will be set if the Glow Plug resistance is not within a calibrated range.
What are the Possible Causes of the DTC P06CB 2016 GMC Sierra?
- Faulty cylinder #1 glow plug
- Cylinder #1 glow plug harness is open or shorted
- Cylinder #1 glow plug circuit poor electrical connection
- Faulty Glow Plug Control Module
How to Fix the DTC P06CB 2016 GMC Sierra?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P06CB 2016 GMC Sierra code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P06CB 2016 GMC Sierra code?
Need more information on how to fix the P06CB 2016 GMC Sierra code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P06CB 2016 GMC Sierra code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P06CB 2016 GMC Sierra Code
What does OBD-II code P06CB mean for a 2016 GMC Sierra?
Code P06CB indicates that the glow plug in cylinder 7 is not functioning correctly, often due to an electrical or mechanical issue.
What are the common symptoms of code P06CB in a 2016 GMC Sierra?
Symptoms include difficulty starting the engine in cold weather, reduced engine performance, and the check engine light illuminating.
What causes the P06CB code to appear?
Possible causes include a faulty cylinder 7 glow plug, damaged wiring or connectors, a failed glow plug control module, or issues with the engine control module (ECM).
How can I diagnose the P06CB code?
Start by inspecting the glow plug, wiring, and connectors for damage. Use a multimeter to test the glow plug's resistance and verify proper operation of the glow plug control module.
Can I drive my 2016 GMC Sierra with code P06CB?
While the vehicle may remain drivable, it could struggle to start in cold weather or experience reduced performance. Prompt repair is recommended to avoid further issues.
How do I fix code P06CB on a 2016 GMC Sierra?
Repairs may include replacing the cylinder 7 glow plug, repairing or replacing damaged wiring, or replacing the glow plug control module if necessary.
How much does it cost to repair the P06CB code?
Glow plug replacement typically costs $50-$150 for the part, plus labor. Module or wiring repairs may increase costs depending on the extent of the damage.
Can a faulty glow plug affect fuel efficiency in a diesel engine?
Yes, a malfunctioning glow plug can impact combustion efficiency, potentially leading to decreased fuel economy and higher emissions.
How can I prevent code P06CB from reoccurring?
Regular maintenance, including periodic inspection of the glow plugs and electrical connections, can help prevent recurrence of this issue.
Is a special tool required to replace a glow plug on a 2016 GMC Sierra?
Yes, a glow plug socket is typically required for removal and installation to avoid damaging the component.
Discuss the causes and fixes for P06CB 2016 GMC Sierra OBDII Code
Code P06CB 2016 GMC Sierra comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
