AutoCodes.com | All About OBDII Engine Codes
AutoCodes - Chevrolet - P06B6 2017 Chevrolet Silverado

P06B6 2017 Chevrolet Silverado Code - Control Module Knock Sensor Processor 1 Performance

- Code Popularity: 197 Views
- Repair Importance Level: 3/3
- Repair Difficulty Level: 3/3
Table of contents
Share on Facebook   Share on Twitter   Share on Linkedin

What are the Possible Causes of the DTC P06B6 2017 Chevrolet Silverado?

NOTE: The causes shown may not be a complete list of all potential problems, and it is possible that there may be other causes.
  • Faulty Knock Sensor Bank 1
  • Knock Sensor Bank 1 circuit poor electrical connection
  • Knock Sensor Bank 1 harness is open or shorted
  • Faulty Engine Control Module (ECM)
⚠ Does your Chevrolet have Safety Recalls? → Check here

How to Fix the DTC P06B6 2017 Chevrolet Silverado?

Review the 'Possible Causes' mentioned above and visually examine the corresponding wiring harness and connectors. Ensure to check for any damaged components and inspect the connector pins for signs of being broken, bent, pushed out, or corroded.

Search for P06B6 2017 Chevrolet Silverado Questions and Answers: Search here →

What is the Cost to Diagnose the Code?

Labor: 1.0

To diagnose the P06B6 2017 Chevrolet Silverado code, it typically requires 1.0 hour of labor. The specific diagnosis time and labor rates at auto repair shops can differ based on factors such as the location, make and model of the vehicle, and even the engine type. It is common for most auto repair shops to charge between $75 and $150 per hour.

What are Code Possible Symptoms?

  • Engine Light ON (or Service Engine Soon Warning Light)

Code P06B6 2017 Chevrolet Silverado Description

The Knock Sensor system enables the Engine Control Module (ECM) to control the ignition timing for the best possible performance while protecting the engine from potentially damaging levels of detonation, also known as spark knock. The knock sensor system uses one or two flat response 2-wire sensors. The sensor uses piezo-electric crystal technology that produces an AC voltage signal of varying amplitude and frequency based on the engine vibration or noise level. The amplitude and frequency are dependent upon the level of knock that the knock sensor detects. The ECM receives the knock sensor signal through two isolated signal circuits for each knock sensor.
The control module learns a minimum noise level, or background noise, at idle from the knock sensor and uses calibrated values for the rest of the RPM range. The control module uses the minimum noise level to calculate a noise channel. A normal knock sensor signal will ride within the noise channel. As engine speed and load change, the noise channel upper and lower parameters will change to accommodate the normal knock sensor signal, keeping the signal within the channel. In order to determine which cylinders are knocking, the control module only uses knock sensor signal information when each cylinder is near the Top Dead Center (TDC) of the firing stroke. If a knock is present, the signal will range outside of the noise channel.
If the control module has determined that a knock is present, it will retard the ignition timing to attempt to eliminate the knock. The control module will always try to work back to a zero-compensation level, or no spark retard. An abnormal knock sensor signal will stay outside of the noise channel or will not be present. knock sensor diagnostics are calibrated to detect faults with the knock sensor circuitry inside the control module, the knock sensor wiring, or the knock sensor voltage output. Some diagnostics are also calibrated to detect constant noise from an outside influence such as a loose/damaged component or excessive engine mechanical noise.
The Diagnostic Trouble Code (DTC) will be set when a fault of the processor that evaluates the knock sensor signal was detected.
OBDII Code P06B6 2017 Chevrolet Silverado - Control Module Knock Sensor Processor 1 Performance - AutoCodes.com
P06B6 2017 Chevrolet Silverado Code - Control Module Knock Sensor Processor 1 Performance

Need More Information on the Code?

Need more information on how to fix the P06B6 2017 Chevrolet Silverado code? Get Access to Factory Service Manuals

Need Help with the Code?

Get the P06B6 2017 Chevrolet Silverado code diagnosed by a professional: Find a repair shop in your area

Code P06B6 2017 Chevrolet Silverado comments

Help us improve AutoCodes.com. Leave a comment below or tell us if the information above helps you fix the code. What are the symptoms on your vehicle for the P06B6 2017 Chevrolet Silverado code? Have you replaced any parts?
Any information is appreciated. Thanks