AutoCodes - Infiniti - P0441 2003 INFINITI G35

P0441 2003 INFINITI G35 Code - Evaporative Control System Incorrect Purge Flow

Repair Importance Level: 1/3
Repair Difficulty Level: 3/3
Table of contents

|P0441 2003 INFINITI G35 code possible causes

  • EVAP canister purge volume control solenoid valve stuck closed
  • EVAP control system pressure sensor and the circuit
  • Loose, disconnected or improper connection of rubber tube
  • Blocked rubber tube
  • Cracked EVAP canister
  • EVAP canister purge volume control solenoid valve circuit
  • Accelerator pedal position sensor
  • Blocked purge port
  • EVAP canister vent control valve

|How do I fix the P0441 2003 INFINITI G35 code?

Check the "Possible Causes" listed above. Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector's pins.

|P0441 2003 INFINITI G35 code tech notes

The P0441 code means that the control module has detected a leak in the Evaporative Emission (EVAP). Loose fuel tank filler cap is the most common cause that triggers the P0441 code.

|Cost of diagnosing the P0441 2003 INFINITI G35 code

Labor: 1.0

The cost of diagnosing the P0441 2003 INFINITI G35 code is 1.0 hour of labor. The auto repair's diagnosis time and labor rates vary by location, vehicle's make and model, and even your engine type. Most auto repair shops charge between $75 and $150 per hour.

|When is the P0441 2003 INFINITI G35 code detected?

EVAP control system does not operate properly, EVAP control system has a leak between intake manifold and EVAP control system pressure sensor.

|What are P0441 2003 INFINITI G35 code possible symptoms?

  • Engine Light ON (or Service Engine Soon Warning Light)
  • Possible a noticeable fuel odor caused by the release of fuel vapors

|P0441 2003 INFINITI G35 code description

The Engine Control Module (ECM) tests the Evaporative Emission (EVAP) system for the following conditions:
- Large and small leaks
- Excess vacuum
- Purge flow during non-commanded conditions
- Fuel Level and Fuel Pressure sensor faults
- EVAP Purge and Vent Valve faults
The ECM monitors the Fuel Tank Pressure sensor in order to determine the level of vacuum/pressure in the EVAP system. The ECM commands both the EVAP Purge Solenoid and the EVAP Vent Valve ON when the conditions are met in order to apply an engine vacuum to the EVAP system. The ECM commands the EVAP Purge Solenoid OFF once the system has reached a predetermined level of vacuum. This test verifies if a vacuum can be achieved in the EVAP system. Failure to develop a vacuum may be caused by a large leak or a restriction.
OBDII Code P0441 2003 Infiniti G35 - Evaporative Control System Incorrect Purge Flow - AutoCodes.com

|Need more information with the P0441 2003 INFINITI G35 code?

Need more information on how to fix the P0441 2003 INFINITI G35 code?
Get Access to Factory Service Manuals

|Need help with a P0441 2003 INFINITI G35 code?

Get the P0441 2003 Infiniti G35 code diagnosed by a professional: Find a repair shop in your area

|P0441 2003 INFINITI G35 code comments

Help us improve AutoCodes.com. Leave a comment below or tell us if the information above helps you fix the code. What are the symptoms on your vehicle for the P0441 2003 Infiniti G35 code? Have you replaced any parts?
Any information is appreciated. Thanks
Top ⇧
Repair Importance Level: 1
 
1=Low 2=Medium 3=High What is this?
Repair Difficulty Level: 3
 
1=Easy 2=Moderate 3=Hard What is this?