P0404 Mitsubishi Code - Exhaust Gas Recirculation Position Sensor Circuit Performance
Quick Answer
Early Exhaust Gas Recirculation (EGR) systems component s include and EGR Valve, and Engine Control Μodule (ECΜ) Controlled Vacuum Switch Valve or EGR Solenoid and an EGR Vacuum Μodulator. Common causes include EGR volume control solenoid valve, EGR volume control solenoid valve harness is open or shorted, EGR volume control solenoid valve circuit poor electrical connection. Severity is Moderate - service should be scheduled soon. The vehicle may still be drivable for short trips if it runs normally, but avoid hard driving and repair it soon.
- What it means
- P0404 Mitsubishi indicates Exhaust Gas Recirculation Position Sensor Circuit Performance.
- Common causes
- Common causes include EGR volume control solenoid valve, EGR volume control solenoid valve harness is open or shorted, EGR volume control solenoid valve circuit poor electrical connection.
- Severity
- Moderate - service should be scheduled soon.
- Can I drive?
- The vehicle may still be drivable for short trips if it runs normally, but avoid hard driving and repair it soon.
Code P0404 Mitsubishi Description
The EGR system on recently built vehicles uses a step motor to control the flow rate of EGR from exhaust manifold. This motor has four winding phases. It operates according to the output pulse signal of the ECΜ. Two windings are turned ON and OFF in sequence. Each time an ON pulse is issued, the valve opens or closes, changing the flow rate. When no change in the flow rate is needed, the ECΜ does not issue the pulse signal. Α certain voltage signal is issued so that the valve remains at that particular opening.
What are the Possible Causes of the DTC P0404 Mitsubishi?
- EGR volume control solenoid valve
- EGR volume control solenoid valve harness is open or shorted
- EGR volume control solenoid valve circuit poor electrical connection
- EGR temperature sensor and circuit
How to Fix the DTC P0404 Mitsubishi?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P0404 Mitsubishi code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P0404 Mitsubishi code?
Need more information on how to fix the P0404 Mitsubishi code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P0404 Mitsubishi code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P0404 Mitsubishi Code
1. What are the common symptoms of OBDII code P0404 in a Mitsubishi related to the Exhaust Gas Recirculation (EGR) Position Sensor Circuit Performance?
The common symptoms include rough idling, decreased fuel efficiency, engine hesitation, and the illumination of the Check Engine Light.
2. What are the possible causes of OBDII code P0404 in a Mitsubishi?
The code P0404 in a Mitsubishi could be triggered by a faulty EGR position sensor, a clogged EGR valve, damaged wiring in the EGR system, or a problem with the EGR control solenoid.
3. How can I diagnose the cause of OBDII code P0404 in my Mitsubishi?
To diagnose the issue, you can use an OBDII scanner to read the code and perform a visual inspection of the EGR system components for any signs of damage or blockages. You may also need to test the EGR position sensor and related wiring for proper functionality.
4. Is it safe to continue driving my Mitsubishi with OBDII code P0404 triggered?
While it may be safe to drive your vehicle with this code in the short term, it is recommended to address the underlying issue promptly to prevent potential long-term damage to the engine or emissions system.
5. How can I repair OBDII code P0404 in my Mitsubishi?
Repairing code P0404 may involve replacing the EGR position sensor, cleaning or replacing the EGR valve, repairing damaged wiring, or addressing any other specific component that is causing the circuit performance issue.
6. Can a DIY enthusiast fix OBDII code P0404 in a Mitsubishi?
Yes, depending on your level of automotive knowledge and experience, you may be able to address the issue yourself by following repair guides or tutorials specific to your Mitsubishi model.
7. Will resetting the Check Engine Light resolve OBDII code P0404 in my Mitsubishi?
Simply resetting the Check Engine Light may temporarily clear the code, but it will not fix the underlying issue causing code P0404. It is essential to diagnose and repair the problem to prevent the code from reappearing.
8. How much does it typically cost to repair OBDII code P0404 in a Mitsubishi at a professional mechanic or dealership?
The cost of repairing code P0404 can vary depending on the specific cause of the issue, the labor rates of the service provider, and the cost of any replacement parts needed. It is advisable to obtain quotes from different repair shops for an accurate estimate.
9. Are there any preventive maintenance tips to avoid OBDII code P0404 in a Mitsubishi?
Regularly servicing your Mitsubishi according to the manufacturer's recommended maintenance schedule, using high-quality fuel, and ensuring the EGR system is clean and functioning properly can help prevent issues that lead to code P0404.
10. What other related OBDII codes might be triggered along with P0404 in a Mitsubishi?
Codes related to the EGR system, such as P0401 (EGR Flow Insufficient) or P0402 (EGR Flow Excessive), may also be triggered along with P0404 in a Mitsubishi experiencing EGR-related issues.
Discuss the causes and fixes for P0404 Mitsubishi OBDII Code
Code P0404 Mitsubishi comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
