P0390 2006 Ford Fusion Code - Camshaft Position Sensor 'B' Circuit Bank 2
Quick Answer
The Camshaft Position Sensor is an electronic device used in an engine to record the rate at which the camshaft is spinning. Common causes include Faulty Camshaft Position Sensor, Camshaft Position Sensor harness is open or shorted, Camshaft Position Sensor circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P0390 2006 Ford Fusion indicates Camshaft Position Sensor 'B' Circuit Bank 2.
- Common causes
- Common causes include Faulty Camshaft Position Sensor, Camshaft Position Sensor harness is open or shorted, Camshaft Position Sensor circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P0390 2006 Ford Fusion Description
When the engine is running, the high and low parts of the teeth cause the gap with the sensor to change. The changing gap causes the magnetic field near the sensor to change. The change in the magnetic field cause the voltage from the sensor to change.
When the crankshaft position sensor (POS) system becomes inoperative, the camshaft position sensor provides various controls of engine parts instead, utilizing timing of cylinder identification signals.
What are the Possible Causes of the DTC P0390 2006 Ford Fusion?
- Faulty Camshaft Position Sensor
- Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
- Faulty starter motor
- Starting system circuit
- Dead (Weak) battery
How to Fix the DTC P0390 2006 Ford Fusion?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
Code Tech Notes
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P0390 2006 Ford Fusion code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P0390 2006 Ford Fusion code?
Need more information on how to fix the P0390 2006 Ford Fusion code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P0390 2006 Ford Fusion code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P0390 2006 Ford Fusion Code
1. What are the common symptoms of OBDII code P0390 on a 2006 Ford Fusion?
The common symptoms include engine misfires, rough idling, difficulty starting the engine, and a decrease in fuel efficiency.
2. What causes the OBDII code P0390 to appear in a 2006 Ford Fusion?
The code P0390 typically indicates a problem with the camshaft position sensor 'B' circuit on Bank 2, which could be due to a faulty sensor, wiring issues, or a problem with the sensor's connection.
3. How can I diagnose the issue causing OBDII code P0390 on my 2006 Ford Fusion?
Diagnosing the issue involves checking the camshaft position sensor 'B' on Bank 2 for any visible damage, testing the sensor's electrical connections, and using a scan tool to monitor sensor data for abnormalities.
4. Can I continue driving my 2006 Ford Fusion with OBDII code P0390 present?
It is not recommended to drive the vehicle with the P0390 code active, as it can lead to further engine damage and potentially unsafe driving conditions.
5. How do I repair OBDII code P0390 on my 2006 Ford Fusion?
Repairing the issue typically involves replacing the faulty camshaft position sensor 'B' on Bank 2, addressing any wiring or connection problems, and clearing the trouble codes from the vehicle's computer.
6. Are there any tips for preventing OBDII code P0390 from reoccurring in my 2006 Ford Fusion?
To help prevent the code from reoccurring, it's essential to use high-quality replacement parts, ensure proper installation of the sensor, and regularly maintain the vehicle's engine components.
7. Can a DIY enthusiast fix OBDII code P0390 on a 2006 Ford Fusion?
Depending on their skill level and experience, a DIY enthusiast may be able to replace the camshaft position sensor 'B' on Bank 2 themselves. However, proper diagnosis and repair are crucial to ensure the issue is correctly resolved.
8. Will resetting the OBDII system clear the P0390 code on my 2006 Ford Fusion?
Resetting the OBDII system may temporarily clear the code, but if the underlying issue causing the P0390 code is not fixed, it is likely to reappear once the problem is detected again.
9. How long does it take to repair OBDII code P0390 on a 2006 Ford Fusion?
The repair time can vary depending on the exact cause of the code and the skill level of the person performing the repair. On average, it may take anywhere from 1 to 3 hours to diagnose and replace the camshaft position sensor 'B' on Bank 2.
10. Is it necessary to take my 2006 Ford Fusion to a mechanic for OBDII code P0390 repair?
While it's possible to diagnose and fix the issue yourself, if you're unsure about the repair process or lack the necessary tools, it's recommended to take your vehicle to a qualified mechanic to ensure the problem is properly addressed.
Discuss the causes and fixes for P0390 2006 Ford Fusion OBDII Code
Code P0390 2006 Ford Fusion comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
