P0345 2010 Nissan Altima Sedan Code - Camshaft Position Sensor Circuit Bank 2
Quick Answer
The Camshaft Position Sensor is an electronic device used in an engine to record the rate at which the camshaft is spinning. Common causes include Faulty Camshaft Position Sensor, Camshaft Position Sensor harness is open or shorted, Camshaft Position Sensor circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P0345 2010 Nissan Altima Sedan indicates Camshaft Position Sensor Circuit Bank 2.
- Common causes
- Common causes include Faulty Camshaft Position Sensor, Camshaft Position Sensor harness is open or shorted, Camshaft Position Sensor circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P0345 2010 Nissan Altima Sedan Description
When the engine is running, the high and low parts of the teeth cause the gap with the sensor to change. The changing gap causes the magnetic field near the sensor to change. The change in the magnetic field cause the voltage from the sensor to change.
When the crankshaft position sensor (POS) system becomes inoperative, the camshaft position sensor provides various controls of engine parts instead, utilizing timing of cylinder identification signals.
What are the Possible Causes of the DTC P0345 2010 Nissan Altima Sedan?
- Faulty Camshaft Position Sensor
- Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
- Faulty starter motor
- Starting system circuit
- Dead (Weak) battery
How to Fix the DTC P0345 2010 Nissan Altima Sedan?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P0345 2010 Nissan Altima Sedan code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P0345 2010 Nissan Altima Sedan code?
Need more information on how to fix the P0345 2010 Nissan Altima Sedan code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P0345 2010 Nissan Altima Sedan code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P0345 2010 Nissan Altima Sedan Code
1. What are the common symptoms of OBDII code P0345 in a 2010 Nissan Altima Sedan?
The common symptoms of code P0345 (Camshaft Position Sensor Circuit Bank 2) in a 2010 Nissan Altima Sedan may include engine misfires, rough idling, poor acceleration, and stalling.
2. What does the OBDII code P0345 indicate in a 2010 Nissan Altima Sedan?
Code P0345 indicates a problem with the Camshaft Position Sensor Circuit Bank 2 in a 2010 Nissan Altima Sedan, specifically related to the camshaft position sensor.
3. What are possible causes of OBDII code P0345 in a 2010 Nissan Altima Sedan?
Possible causes of code P0345 in a 2010 Nissan Altima Sedan include a faulty camshaft position sensor, wiring issues in the camshaft position sensor circuit, or a problem with the sensor's connection.
4. How can I diagnose the cause of OBDII code P0345 in my 2010 Nissan Altima Sedan?
To diagnose the cause of code P0345 in a 2010 Nissan Altima Sedan, you can perform a visual inspection of the camshaft position sensor and its wiring, use a multimeter to test the sensor's electrical connections, and scan the car's computer for additional fault codes.
5. Is it safe to drive my 2010 Nissan Altima Sedan with OBDII code P0345?
It is not recommended to drive your 2010 Nissan Altima Sedan with code P0345 as it can lead to engine performance issues and potential stalling, which can compromise your safety on the road.
6. How can I repair OBDII code P0345 in a 2010 Nissan Altima Sedan?
To repair code P0345 in a 2010 Nissan Altima Sedan, you may need to replace the camshaft position sensor, repair any damaged wiring in the sensor circuit, or ensure a secure connection for the sensor.
7. Can a DIY enthusiast fix OBDII code P0345 in a 2010 Nissan Altima Sedan?
If you have the necessary tools and automotive repair experience, you may be able to fix code P0345 in a 2010 Nissan Altima Sedan as it typically involves replacing a sensor or fixing wiring issues.
8. How much does it cost to repair OBDII code P0345 in a 2010 Nissan Altima Sedan?
The cost to repair code P0345 in a 2010 Nissan Altima Sedan can vary depending on the cause of the issue, but it may range from $100 to $300 for parts and labor.
9. Will resetting the OBDII code P0345 in my 2010 Nissan Altima Sedan make it go away permanently?
Resetting the OBDII code P0345 in a 2010 Nissan Altima Sedan may temporarily clear the code, but if the underlying issue with the camshaft position sensor circuit is not fixed, the code is likely to reappear.
10. Can a bad camshaft position sensor cause other problems besides triggering OBDII code P0345 in a 2010 Nissan Altima Sedan?
Yes, a bad camshaft position sensor in a 2010 Nissan Altima Sedan can cause other issues such as poor fuel economy, difficulty starting the engine, and even potential damage to the catalytic converter over time.
Discuss the causes and fixes for P0345 2010 Nissan Altima Sedan OBDII Code
Code P0345 2010 Nissan Altima Sedan comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
