P0340 2013 Nissan Rogue Code - Camshaft Position Sensor Circuit Bank 1
Quick Answer
The Camshaft Position Sensor is an electronic device used in an engine to record the rate at which the camshaft is spinning. Common causes include Faulty Camshaft Position Sensor, Camshaft Position Sensor harness is open or shorted, Camshaft Position Sensor circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P0340 2013 Nissan Rogue indicates Camshaft Position Sensor Circuit Bank 1 .
- Common causes
- Common causes include Faulty Camshaft Position Sensor, Camshaft Position Sensor harness is open or shorted, Camshaft Position Sensor circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P0340 2013 Nissan Rogue Description
When the engine is running, the high and low parts of the teeth cause the gap with the sensor to change. The changing gap causes the magnetic field near the sensor to change. The change in the magnetic field cause the voltage from the sensor to change.
When the crankshaft position sensor (POS) system becomes inoperative, the camshaft position sensor provides various controls of engine parts instead, utilizing timing of cylinder identification signals.
What are the Possible Causes of the DTC P0340 2013 Nissan Rogue?
- Faulty Camshaft Position Sensor
- Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
- Faulty starter motor
- Starting system circuit
- Dead (Weak) battery
How to Fix the DTC P0340 2013 Nissan Rogue?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
Code Tech Notes
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P0340 2013 Nissan Rogue code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P0340 2013 Nissan Rogue code?
Need more information on how to fix the P0340 2013 Nissan Rogue code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P0340 2013 Nissan Rogue code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P0340 2013 Nissan Rogue Code
1. What are the common symptoms of OBDII code P0340 in a 2013 Nissan Rogue?
The common symptoms of OBDII code P0340 in a 2013 Nissan Rogue include engine misfires, rough idling, stalling, poor acceleration, and the Check Engine light illuminating on the dashboard.
2. What does OBDII code P0340 indicate in a 2013 Nissan Rogue?
OBDII code P0340 in a 2013 Nissan Rogue indicates a problem with the Camshaft Position Sensor Circuit Bank 1.
3. What are the possible causes of OBDII code P0340 in a 2013 Nissan Rogue?
Possible causes of OBDII code P0340 in a 2013 Nissan Rogue include a faulty camshaft position sensor, damaged wiring or connectors in the camshaft position sensor circuit, or issues with the timing belt or chain.
4. How can I diagnose the Camshaft Position Sensor Circuit Bank 1 issue in a 2013 Nissan Rogue?
To diagnose the Camshaft Position Sensor Circuit Bank 1 issue in a 2013 Nissan Rogue, you can use an OBDII scanner to read the trouble code, visually inspect the camshaft position sensor and its wiring, and perform voltage and continuity tests on the sensor.
5. Can I continue driving my 2013 Nissan Rogue with OBDII code P0340?
It is not recommended to continue driving your 2013 Nissan Rogue with OBDII code P0340, as it can lead to further engine damage and potential safety hazards. It is best to address the issue promptly.
6. How do I repair OBDII code P0340 in my 2013 Nissan Rogue?
To repair OBDII code P0340 in a 2013 Nissan Rogue, you may need to replace the camshaft position sensor, repair or replace damaged wiring or connectors, and ensure proper installation and calibration of the new sensor.
7. Can a DIY enthusiast fix OBDII code P0340 in a 2013 Nissan Rogue?
A DIY enthusiast with the necessary tools and knowledge about automotive repair may be able to fix OBDII code P0340 in a 2013 Nissan Rogue, especially if the issue is related to the camshaft position sensor replacement or wiring repair.
8. How much does it cost to repair OBDII code P0340 in a 2013 Nissan Rogue?
The cost to repair OBDII code P0340 in a 2013 Nissan Rogue can vary depending on the root cause of the issue, labor costs in your area, and whether you choose to address the problem yourself or take it to a professional mechanic. Costs may range from $100 to $500 or more.
9. Are there any preventive maintenance tips to avoid OBDII code P0340 in a 2013 Nissan Rogue?
To help prevent OBDII code P0340 in a 2013 Nissan Rogue, it is recommended to follow the manufacturer's recommended maintenance schedule, regularly inspect and replace the camshaft position sensor as needed, and address any engine performance issues promptly.
10. How long does it take to fix OBDII code P0340 in a 2013 Nissan Rogue?
The time it takes to fix OBDII code P0340 in a 2013 Nissan Rogue can vary based on the specific repair needed, the availability of parts, and the skill level of the person performing the repair. Generally, it may take a few hours to a full day to complete the repair.
Discuss the causes and fixes for P0340 2013 Nissan Rogue OBDII Code
Code P0340 2013 Nissan Rogue comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
