P0340 2005 Nissan Xterra Code - Camshaft Position Sensor Circuit Bank 1
Quick Answer
The Camshaft Position Sensor is an electronic device used in an engine to record the rate at which the camshaft is spinning. Common causes include Faulty Camshaft Position Sensor, Camshaft Position Sensor harness is open or shorted, Camshaft Position Sensor circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P0340 2005 Nissan Xterra indicates Camshaft Position Sensor Circuit Bank 1 .
- Common causes
- Common causes include Faulty Camshaft Position Sensor, Camshaft Position Sensor harness is open or shorted, Camshaft Position Sensor circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P0340 2005 Nissan Xterra Description
When the engine is running, the high and low parts of the teeth cause the gap with the sensor to change. The changing gap causes the magnetic field near the sensor to change. The change in the magnetic field cause the voltage from the sensor to change.
When the crankshaft position sensor (POS) system becomes inoperative, the camshaft position sensor provides various controls of engine parts instead, utilizing timing of cylinder identification signals.
*Sensor design may vary for your model and year
What are the Possible Causes of the DTC P0340 2005 Nissan Xterra?
- Faulty Camshaft Position Sensor
- Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
- Faulty starter motor
- Starting system circuit
- Dead (Weak) battery
How to Fix the DTC P0340 2005 Nissan Xterra?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P0340 2005 Nissan Xterra code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P0340 2005 Nissan Xterra code?
Need more information on how to fix the P0340 2005 Nissan Xterra code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P0340 2005 Nissan Xterra code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P0340 2005 Nissan Xterra Code
1. What are the common symptoms of OBDII code P0340 in a 2005 Nissan Xterra?
- Common symptoms include engine misfires, rough idling, difficulty starting the vehicle, and a decrease in fuel efficiency.
2. What does OBDII code P0340 on a 2005 Nissan Xterra indicate?
- OBDII code P0340 indicates a problem with the Camshaft Position Sensor Circuit Bank 1 in the vehicle.
3. What are the possible causes of OBDII code P0340 in a 2005 Nissan Xterra?
- Possible causes include a faulty camshaft position sensor, wiring issues in the sensor circuit, a malfunctioning camshaft sensor connector, or a timing belt problem.
4. How can I diagnose the Camshaft Position Sensor Circuit Bank 1 issue in my 2005 Nissan Xterra?
- You can diagnose the issue by using an OBDII scanner to read the error code, visually inspecting the sensor and its wiring for any damage, and testing the sensor's voltage and signal.
5. Can I drive my 2005 Nissan Xterra with OBDII code P0340?
- It is not recommended to drive the vehicle with OBDII code P0340 as it can lead to further engine damage and potential safety hazards.
6. How much does it typically cost to repair OBDII code P0340 in a 2005 Nissan Xterra?
- The cost of repairing OBDII code P0340 can vary depending on the exact cause of the issue, but it typically ranges from $100 to $300 for parts and labor.
7. Are there any DIY repair tips for fixing OBDII code P0340 in a 2005 Nissan Xterra?
- DIY repair tips include checking and cleaning the camshaft position sensor connector, ensuring proper wiring connections, and following the vehicle's service manual for guidance.
8. Can a faulty camshaft position sensor cause other issues in a 2005 Nissan Xterra?
- Yes, a faulty camshaft position sensor can lead to poor engine performance, reduced fuel efficiency, and potential stalling of the vehicle.
9. Is it necessary to reset the OBDII code after repairing P0340 in a 2005 Nissan Xterra?
- Yes, it is recommended to reset the OBDII code after repairing P0340 to clear the error code from the system and ensure proper functioning of the vehicle.
10. How often should the camshaft position sensor be replaced in a 2005 Nissan Xterra?
- The camshaft position sensor does not have a specific replacement interval, but it is recommended to replace it when symptoms of failure appear or during routine maintenance checks.
Discuss the causes and fixes for P0340 2005 Nissan Xterra OBDII Code
-
Hey just wanted to say thnx you for this video. I will attempt this tomorrow. Here in a suburb of houston texas.
-
I love my Nissan Exterra bit would not recommend anyone buying a Nissan because nog garage wants to touch it and ss so expensive to fix it. 5 sensors replaced emmision control replaced and 2 tire rod ends replaced and another part that has something to do with the engine only has 119,000 miles on it do some research before buying a Nissan could save u tons of $ Ill be trading mine in soon
-
PLEASE NOTE: The video linked above is for the CRANKSHAFT sensor, not the camshaft sensor which produces the code and symptoms described. P0340 code is caused by the passenger side (bank 1) CAMSHAFT sensor, which is located at the back of the passenger side valve cover, behind and below the intake manifold.
-
Replace timing chain components, replaced both camshaft sensors two months ago, now the code came back and it will stall and hard starting after warm up, if I clear code will run for a couple of days before it stops again
-
What are the readings on the sensor and wiring I should be looking for
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
