P0340 2004 Nissan Maxima Code - Camshaft Position Sensor Circuit Bank 1
Quick Answer
The Camshaft Position Sensor is an electronic device used in an engine to record the rate at which the camshaft is spinning. Common causes include Faulty Camshaft Position Sensor, Camshaft Position Sensor harness is open or shorted, Camshaft Position Sensor circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P0340 2004 Nissan Maxima indicates Camshaft Position Sensor Circuit Bank 1 .
- Common causes
- Common causes include Faulty Camshaft Position Sensor, Camshaft Position Sensor harness is open or shorted, Camshaft Position Sensor circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P0340 2004 Nissan Maxima Description
When the engine is running, the high and low parts of the teeth cause the gap with the sensor to change. The changing gap causes the magnetic field near the sensor to change. The change in the magnetic field causes the voltage from the sensor to change.
When the crankshaft position sensor (POS) system becomes inoperative, the camshaft position sensor provides various controls of engine parts instead, utilizing the timing of cylinder identification signals.
What are the Possible Causes of the DTC P0340 2004 Nissan Maxima?
- Faulty Camshaft Position Sensor
- Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
- Faulty starter motor
- Starting system circuit
- Dead (Weak) battery
How to Fix the DTC P0340 2004 Nissan Maxima?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
Code Tech Notes
2004 Nissan Maxima Factory Service Bulletin OBDII Code P0340
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P0340 2004 Nissan Maxima code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P0340 2004 Nissan Maxima code?
Need more information on how to fix the P0340 2004 Nissan Maxima code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P0340 2004 Nissan Maxima code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P0340 2004 Nissan Maxima Code
1. What does OBDII code P0340 mean for a 2004 Nissan Maxima?
Code P0340 indicates a problem with the Camshaft Position Sensor Circuit Bank 1 in a 2004 Nissan Maxima.
2. What are the common symptoms of a P0340 code in a 2004 Nissan Maxima?
Common symptoms include engine misfires, rough idling, difficulty starting the engine, and decreased fuel efficiency.
3. What are the possible causes of a P0340 code in a 2004 Nissan Maxima?
Potential causes include a faulty camshaft position sensor, damaged wiring or connectors, issues with the timing belt or chain, or a problem with the PCM (Powertrain Control Module).
4. How can I diagnose the cause of a P0340 code in my 2004 Nissan Maxima?
Diagnosis typically involves checking the camshaft position sensor and related components for proper functioning, inspecting wiring and connectors for damage, and performing a thorough visual inspection of the timing components.
5. Can I drive my 2004 Nissan Maxima with a P0340 code?
It is not recommended to drive the vehicle with a P0340 code, as it can lead to further engine damage and potentially unsafe driving conditions.
6. How do I repair a P0340 code in a 2004 Nissan Maxima?
Repairing a P0340 code may involve replacing the camshaft position sensor, repairing damaged wiring or connectors, adjusting the timing belt or chain, or reprogramming the PCM.
7. Is it possible to reset a P0340 code in a 2004 Nissan Maxima?
Resetting the code may temporarily turn off the check engine light, but it will not fix the underlying issue causing the P0340 code.
8. How much does it cost to repair a P0340 code in a 2004 Nissan Maxima?
The cost of repairing a P0340 code can vary depending on the specific issue, but it may range from $100 to $500 or more, including parts and labor.
9. Can a DIY enthusiast repair a P0340 code in a 2004 Nissan Maxima?
While some individuals with mechanical knowledge may be able to diagnose and repair a P0340 code themselves, it is recommended to consult a professional mechanic for accurate diagnosis and proper repair.
10. Are there any preventive measures to avoid a P0340 code in a 2004 Nissan Maxima?
Regular maintenance, such as inspecting and replacing the camshaft position sensor at recommended intervals, can help prevent issues that may trigger a P0340 code in a 2004 Nissan Maxima.
Discuss the causes and fixes for P0340 2004 Nissan Maxima OBDII Code
-
Helpful information.
Multimeter reads 12.4v and 13.8v with the engine on, so I figured it's not a battery issue.
The code was 0340 so removed the front bank sensor, just below the breather pipe in a 2004 maxima. Squeeze the green clip toward the sensor and it pops out.
Waiting for the replacement part (~au$95 retail) now. -
Fitted the replacement sensor. Code remained so did a code reset.
No more check engine light. Car running well. -
Today the engine stalled and threw up code 0340 again, with the new sensor. The clip is in good condition, just a little dirty. I know it's not the sensor so I will clean the connector tomorrow and see what happens.
-
Could you swap the sensor from the other side, just to check if the problem is the sensor or the connector? which sensor are you replacing the radiator side or the firewall side? Is it possible that you replaced the wrong side?
-
Changed the front back as per the diagram you posted. The cam sensor at the front of engine in bank 1, as per the code. I cleaned the connector but didn't want to tear it open to check continuity. Changed the rear bank sensor and no more code. I was expecting a code 0345 for the rear bank cam sensor but never got a 0345 yet the problem seems to be fixed.
-
The reason changing the front sensor didnt work and the rear did fix the issue is that the rear band is bank 1. The front bank is bank 2.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
