P0339 2009 Honda Accord Code - Crankshaft Position Sensor 'A' Circuit Intermittent
Quick Answer
The Crankshaft position sensor also known as the crank position sensor is an electronic device used in an engine to record the rate at which the crankshaft is spinning. Common causes include Faulty crankshaft position sensor, Crankshaft position sensor harness is open or shorted, Crankshaft position sensor circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P0339 2009 Honda Accord indicates Crankshaft Position Sensor 'A' Circuit Intermittent.
- Common causes
- Common causes include Faulty crankshaft position sensor, Crankshaft position sensor harness is open or shorted, Crankshaft position sensor circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P0339 2009 Honda Accord Description
When the engine is running, the high and low parts of the teeth cause the gap with the sensor to change. The changing gap causes the magnetic field near the sensor to change. The change in the magnetic field cause the voltage from the sensor to change.
What are the Possible Causes of the DTC P0339 2009 Honda Accord?
- Faulty crankshaft position sensor
- Crankshaft position sensor harness is open or shorted
- Crankshaft position sensor circuit poor electrical connection
- Signal plate may be damage
- Starter motor may be faulty
- Starting system circuit
- Dead or weak battery
How to Fix the DTC P0339 2009 Honda Accord?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
Code Tech Notes
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P0339 2009 Honda Accord code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P0339 2009 Honda Accord code?
Need more information on how to fix the P0339 2009 Honda Accord code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P0339 2009 Honda Accord code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P0339 2009 Honda Accord Code
1. What are the common symptoms of OBDII code P0339 in a 2009 Honda Accord?
The common symptoms of OBDII code P0339 in a 2009 Honda Accord include engine stalling, rough idling, difficulty starting the vehicle, and a noticeable decrease in engine performance.
2. What does the OBDII code P0339 indicate in a 2009 Honda Accord?
OBDII code P0339 in a 2009 Honda Accord indicates a problem with the Crankshaft Position Sensor 'A' Circuit Intermittent.
3. What are the possible causes of OBDII code P0339 in a 2009 Honda Accord?
The possible causes of OBDII code P0339 in a 2009 Honda Accord include a faulty crankshaft position sensor, damaged wiring or connectors in the sensor circuit, or issues with the sensor's alignment or installation.
4. How can I diagnose the OBDII code P0339 in my 2009 Honda Accord?
Diagnosing OBDII code P0339 in a 2009 Honda Accord involves checking the crankshaft position sensor for proper operation, inspecting the sensor's wiring and connectors for damage, and ensuring the sensor is correctly aligned and installed.
5. Can I continue driving my 2009 Honda Accord with OBDII code P0339?
It is not recommended to continue driving your 2009 Honda Accord with OBDII code P0339, as it can lead to further engine issues and potential breakdowns. It's best to address the problem promptly.
6. How can I repair OBDII code P0339 in my 2009 Honda Accord?
Repairing OBDII code P0339 in a 2009 Honda Accord typically involves replacing the faulty crankshaft position sensor, repairing any damaged wiring or connectors, and ensuring proper alignment and installation of the sensor.
7. Will resetting the OBDII code P0339 in my 2009 Honda Accord make it go away permanently?
Resetting the OBDII code P0339 in a 2009 Honda Accord may temporarily remove the warning light, but if the underlying issue is not addressed, the code is likely to reappear. It's important to diagnose and repair the problem to prevent recurrence.
8. Can a DIY enthusiast fix OBDII code P0339 in a 2009 Honda Accord?
Depending on your mechanical skills and access to tools, a DIY enthusiast may be able to fix OBDII code P0339 in a 2009 Honda Accord by following repair guides and instructions. However, professional help is recommended for accurate diagnosis and repair.
9. How much does it cost to repair OBDII code P0339 in a 2009 Honda Accord?
The cost to repair OBDII code P0339 in a 2009 Honda Accord can vary depending on the specific cause of the issue, labor rates in your area, and whether you choose to replace the sensor yourself or have it done by a professional. Costs typically range from $100 to $300.
10. Can a faulty crankshaft position sensor cause other issues besides triggering OBDII code P0339 in a 2009 Honda Accord?
Yes, a faulty crankshaft position sensor in a 2009 Honda Accord can cause other issues such as poor fuel economy, misfiring, and problems with the vehicle's transmission, as the sensor plays a crucial role in engine performance and timing.
Discuss the causes and fixes for P0339 2009 Honda Accord OBDII Code
-
Getting code p0339 on 09 Accord. Part shop ran it and said it is crankshaft position sensor. I can replace it but dont have device to clear code. Will it hurt to replace and drive it to have code cleared.
-
After you replace the sensor, you can just disconnect the car battery for about 30 min to clear the code. Nothing will happen if you don't clear the code, eventually the light will off by itself (may take several weeks)
-
I got and new engine with a 28k milles everything works great but when I wantto push the gas car won't go and and also sound like suffocate The car of u stay u u under 4 rpm all good! After ran the car for like 2 hours car won't go I really don't know what going on. :( thansk
-
1. Start the engine. Hold the engine speed at 3,000 rpm (min ?1 ) without load (in neutral) until the radiator fan comes on.
2. Test-drive the vehicle on a level road: Decelerate (with the throttle fully closed) from an engine speed of 2,500 rpm (min ?1 ) down to 1,000 rpm (min ?1 ) with transmission in 1st gear.
3. Test-drive the vehicle on a level road: Decelerate (with the throttle fully closed) from an engine speed of 5,000 rpm (min ?1 ) down to 3,000 rpm (min ?1 ) with transmission in 1st gear.
4. Repeat step 2 and 3 several times.
5. Turn the ignition switch OFF.
6. Turn the ignition switch ON (II), and wait for 30 seconds. The CKP pattern learn procedure is complete.
-
Hi, I attempted the relearn process above, no luck. I bought the Honda Accord OEM part (37500-R40-A01Sensor Assembly, Crank) replaced it and it self corrected.
Additional, I drove it for a day, check engine light turned back on. I reset the code (I did not due previously) and now it runs good. However, the light came back on, I ran the code reader and resulted with P0139 HONDA - HO2S Bank 1 Sensor 2 Slow Response. I am replacing it ASAP.
Can anyone give me a detail location for it (photos/diagrams)?
Thank you
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
