P0335 2013 Toyota RAV4 Code - Crankshaft Position Sensor 'A' Circuit
Quick Answer
The Crankshaft Position Sensor system consists of a crank angle sensor plate and a pickup coil. Common causes include Faulty crankshaft position sensor, Crankshaft position sensor harness is open or shorted, Crankshaft position sensor circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P0335 2013 Toyota RAV4 indicates Crankshaft Position Sensor 'A' Circuit .
- Common causes
- Common causes include Faulty crankshaft position sensor, Crankshaft position sensor harness is open or shorted, Crankshaft position sensor circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P0335 2013 Toyota RAV4 Description
The sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of wound copper wire, an iron core, and a magnet. The crank angle sensor plate rotates and, as each tooth passes by the pickup coil, a pulse signal is created. The pickup coil generates 34 signals per crankshaft revolution. Based on these signals, the Engine Control Module (ECM) calculates the crankshaft position and engine speed. Using these calculations, the fuel injection and ignition timing are controlled. If there is no signal from the crankshaft position sensor despite the crankshaft rotating, the ECM interprets this as a malfunction of the sensor and the Diagnostic Trouble Code (DTC) will be set.
What are the Possible Causes of the DTC P0335 2013 Toyota RAV4?
- Faulty crankshaft position sensor
- Crankshaft position sensor harness is open or shorted
- Crankshaft position sensor circuit poor electrical connection
- Signal plate may be damaged
- Starter motor may be faulty
- Dead or weak battery
- Faulty Engine Control Module (ECM)
How to Fix the DTC P0335 2013 Toyota RAV4?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
Code Tech Notes
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P0335 2013 Toyota RAV4 code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P0335 2013 Toyota RAV4 code?
Need more information on how to fix the P0335 2013 Toyota RAV4 code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P0335 2013 Toyota RAV4 code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P0335 2013 Toyota RAV4 Code
1. What does the OBDII code P0335 mean on a 2013 Toyota RAV4?
P0335 indicates a malfunction in the Crankshaft Position Sensor 'A' Circuit, which monitors the position and rotational speed of the crankshaft.
2. What are the symptoms of the P0335 code in a 2013 Toyota RAV4?
Common symptoms include difficulty starting the engine, stalling, poor acceleration, reduced fuel efficiency, and the check engine light turning on.
3. What causes the P0335 code on a 2013 Toyota RAV4?
Potential causes include a faulty crankshaft position sensor, damaged wiring or connectors, a failed reluctor ring, or issues with the engine control module (ECM).
4. Can I drive my 2013 Toyota RAV4 with the P0335 code?
Driving with the P0335 code is not recommended, as it can lead to stalling and unsafe driving conditions. It should be addressed promptly.
5. How is the P0335 code diagnosed on a 2013 Toyota RAV4?
A technician will use a scan tool to confirm the code, inspect the crankshaft position sensor and its wiring, test the sensor's signal, and check the ECM for faults.
6. How do you fix the P0335 code on a 2013 Toyota RAV4?
Repairs may involve replacing the crankshaft position sensor, repairing damaged wiring, cleaning or replacing the reluctor ring, or reprogramming the ECM if necessary.
7. What tools are needed to fix the P0335 code on a 2013 Toyota RAV4?
Common tools include an OBDII scan tool, a multimeter for testing electrical circuits, and basic hand tools for sensor replacement.
8. How much does it cost to fix the P0335 code on a 2013 Toyota RAV4?
Repair costs vary but can range from $100 to $300, depending on parts and labor required for sensor replacement or wiring repairs.
9. Can a dirty reluctor ring cause the P0335 code on a 2013 Toyota RAV4?
Yes, a dirty or damaged reluctor ring can cause improper readings, leading to the P0335 code.
10. Does a bad battery cause the P0335 code in a 2013 Toyota RAV4?
While unlikely, a weak or failing battery can cause voltage issues that may affect the crankshaft position sensor circuit and trigger the P0335 code.
Discuss the causes and fixes for P0335 2013 Toyota RAV4 OBDII Code
Code P0335 2013 Toyota RAV4 comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
