AutoCodes.com | All About OBDII Engine Codes
AutoCodes - Nissan - P0335 2011 Nissan Xterra

P0335 2011 Nissan Xterra Code - Crankshaft Position Sensor Circuit

- Code Popularity: 8,346 Views
- Repair Importance Level: 3/3
- Repair Difficulty Level: 2/3
Table of contents
By AutoCodes.com - Updated Jun 14, 2020
Share on Facebook   Share on Twitter   Share on Linkedin

|Code P0335 2011 Nissan Xterra Possible Causes

  • Faulty crankshaft position sensor
  • Crankshaft position sensor harness is open or shorted
  • Crankshaft position sensor circuit poor electrical connection
  • Signal plate may be damage
  • Starter motor may be faulty
  • Starting system circuit
  • Dead or weak battery

|How do I Fix the Code P0335 2011 Nissan Xterra?

Check the "Possible Causes" listed above. Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector's pins.

Does your Nissan have Safety Recalls? → Check here

|Code P0335 2011 Nissan Xterra Tech Notes

Sometimes and in some models, low battery voltage or a weak starter can trigger a Crankshaft Position Sensor code. Before replacing any parts, recharge or replace the battery.

2005 Xterra Crankshaft Position Sensor Replacement




User Submitted Video

|What is the Cost to Diagnose the Code P0335 2011 Nissan Xterra?

Labor: 1.0

The cost of diagnosing the P0335 2011 Nissan Xterra code is 1.0 hour of labor. The auto repair labor rates vary by location, your vehicle's make and model, and even your engine type. Most auto repairs shops charge between $75 and $150 per hour.

|When is the Code P0335 2011 Nissan Xterra Detected?

The crankshaft position sensor (POS) signal is not detected by the Electronic Control Module (ECM) during the first few seconds of engine cranking

|What are Code P0335 2011 Nissan Xterra Possible Symptoms?

  • Engine Light ON (or Service Engine Soon Warning Light)
  • Possible lack/loss of Power
  • Engine may stall while driving

|Code P0335 2011 Nissan Xterra Description

The Crankshaft Position Sensor (CKP) also known as the crank position sensor is an electronic device used in an engine to record the rate at which the crankshaft is spinning. This information is used by the Electronic Control Module(ECM) to control ignition and fuel injection. The sensor system consists of a rotating part, typically a disc, as well as a static part, the actual sensor.
When the engine is running, the high and low parts of the teeth cause the gap with the sensor to change. The changing gap causes the magnetic field near the sensor to change. The change in the magnetic field cause the voltage from the sensor to change.

OBDII Code P0335 2011 Nissan Xterra - Crankshaft Position Sensor Circuit - AutoCodes.com
P0335 2011 Nissan Xterra Code - Crankshaft Position Sensor Circuit

|Need More Information on the P0335 2011 Nissan Xterra Code?

Need more information on how to fix the P0335 2011 Nissan Xterra code? Get Access to Factory Service Manuals

|Need Help with the P0335 2011 Nissan Xterra Code?

Get the P0335 2011 Nissan Xterra code diagnosed by a professional: Find a repair shop in your area

|Code P0335 2011 Nissan Xterra comments

Help us improve AutoCodes.com. Leave a comment below or tell us if the information above helps you fix the code. What are the symptoms on your vehicle for the P0335 2011 Nissan Xterra code? Have you replaced any parts?
Any information is appreciated. Thanks