P0335 2009 Nissan Altima Sedan Code - Crankshaft Position Sensor Circuit
Quick Answer
The Crankshaft Position Sensor (CKP) also known as the crank position sensor is an electronic device used in an engine to record the rate at which the crankshaft is spinning. Common causes include Faulty crankshaft position sensor, Crankshaft position sensor harness is open or shorted, Crankshaft position sensor circuit poor electrical connection. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P0335 2009 Nissan Altima Sedan indicates Crankshaft Position Sensor Circuit.
- Common causes
- Common causes include Faulty crankshaft position sensor, Crankshaft position sensor harness is open or shorted, Crankshaft position sensor circuit poor electrical connection.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Code P0335 2009 Nissan Altima Sedan Description
When the engine is running, the high and low parts of the teeth cause the gap with the sensor to change. The changing gap causes the magnetic field near the sensor to change. The change in the magnetic field cause the voltage from the sensor to change.
What are the Possible Causes of the DTC P0335 2009 Nissan Altima Sedan?
- Faulty crankshaft position sensor
- Crankshaft position sensor harness is open or shorted
- Crankshaft position sensor circuit poor electrical connection
- Signal plate may be damage
- Starter motor may be faulty
- Starting system circuit
- Dead or weak battery
How to Fix the DTC P0335 2009 Nissan Altima Sedan?
Review the 'Possible Causes' above and visually examine the corresponding wiring harness and connectors. Check for damaged components and inspect connector pins for signs of being broken, bent, pushed out, or corroded.
Code Tech Notes
What is the Cost to Diagnose the Code?
Labor: 1.0
To diagnose the P0335 2009 Nissan Altima Sedan code, it typically requires 1.0 hour of labor. Rates vary by location, vehicle, and shop. Many shops charge between $80–$150 per hour; dealerships and metro areas may be higher, independents may be lower.
Need more information about the P0335 2009 Nissan Altima Sedan code?
Need more information on how to fix the P0335 2009 Nissan Altima Sedan code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P0335 2009 Nissan Altima Sedan code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P0335 2009 Nissan Altima Sedan Code
1. What are the common symptoms of OBDII code P0335 on a 2009 Nissan Altima Sedan?
- Common symptoms include stalling, rough idling, difficulty starting the engine, and a decrease in fuel efficiency.
2. What does OBDII code P0335 indicate in a 2009 Nissan Altima Sedan?
- OBDII code P0335 indicates a problem with the crankshaft position sensor circuit in the 2009 Nissan Altima Sedan.
3. What are the possible causes of OBDII code P0335 on a 2009 Nissan Altima Sedan?
- Possible causes include a faulty crankshaft position sensor, damaged wiring or connectors in the sensor circuit, or a malfunctioning engine control module (ECM).
4. How can I diagnose the cause of OBDII code P0335 on my 2009 Nissan Altima Sedan?
- Diagnose the code by checking the crankshaft position sensor's wiring and connectors for damage, testing the sensor's resistance, and scanning the ECM for any related trouble codes.
5. Can a faulty crankshaft position sensor affect the performance of a 2009 Nissan Altima Sedan?
- Yes, a faulty crankshaft position sensor can lead to engine performance issues like misfiring, rough idling, and stalling in a 2009 Nissan Altima Sedan.
6. Is it safe to continue driving a 2009 Nissan Altima Sedan with OBDII code P0335?
- It is not recommended to continue driving the vehicle with code P0335 as it can lead to further engine damage or complete engine failure.
7. How much does it typically cost to repair OBDII code P0335 on a 2009 Nissan Altima Sedan?
- The cost of repairing OBDII code P0335 can vary depending on the cause, but it may range from $150 to $400, including parts and labor.
8. Can I repair OBDII code P0335 on a 2009 Nissan Altima Sedan myself?
- If you have the necessary tools and knowledge, you may be able to replace the crankshaft position sensor or repair the wiring yourself. However, professional diagnosis and repair are recommended for accurate troubleshooting.
9. Will resetting the OBDII code P0335 on a 2009 Nissan Altima Sedan make it go away?
- Resetting the code may temporarily clear the error, but if the underlying issue, such as a faulty sensor or wiring problem, is not fixed, the code is likely to reappear.
10. How important is it to address OBDII code P0335 promptly on a 2009 Nissan Altima Sedan?
- It is crucial to address OBDII code P0335 promptly to prevent potential engine performance issues, further damage, or safety hazards while driving the 2009 Nissan Altima Sedan.
Discuss the causes and fixes for P0335 2009 Nissan Altima Sedan OBDII Code
-
My Nissan Altima 2.5 SL stalls sometimes and shuts off mostly at bends. When scanned it showed P0335, I've replaced the sensor, it's better now but still shuts off when I slow down to negotiate a bend, I want to clean up the nozzles today and hope it stops completely
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
